Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 387 | Manualshive

Page: 387 / 532

background image

CAUTION!

Tow hooks are for emergency use only, to rescue a
vehicle stranded off road. Do not use tow hooks for
tow truck hookup or highway towing. You could
damage your vehicle.

TOWING A DISABLED VEHICLE

Proper towing or lifting equipment is required to prevent
damage to your vehicle. Use only tow bars and other
equipment designed for the purpose, following equip-
ment manufacturer’s instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to
the main structural members of the vehicle—not to
bumpers or associated brackets. State and local laws
applying to vehicles under tow must be observed.

4-Wheel- Drive Vehicles

CAUTION!

To avoid damage to the transfer case while towing,
always use one of the following methods.

NOTE:

The Transfer Case must be in the neutral posi-

tion, and the transmission must be in Park (Automatic
Transmission), or in gear (Manual Transmission) to tow a
4WD vehicle with one end of the vehicle raised.

WHAT TO DO IN EMERGENCIES

387

6

«
...
385
386
387
388
389
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Oldsmobile Pages: 360

Brand: Vaisala Pages: 24

Brand: Honda Pages: 73

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: Toro Pages: 24

Brand: NavLinkz Pages: 21

Brand: Saturn Pages: 440

Brand: Kia Pages: 58

Brand: Pontiac Pages: 20

Brand: Dakota Digital Pages: 20

Brand: Aries Pages: 3

Dodge Caravan 2002

Brand: Chrysler Pages: 2399

Brand: Ednet Pages: 6

Brand: Renault Pages: 11

Brand: MayPole Pages: 3

Brand: HAKR Pages: 2

Brand: RAM Pages: 288

Brand: JVC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands