Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 99

Page: 99 / 532

•

An active call is automatically transferred to the
mobile phone after ignition key is switched to off.

UConnect™ System Features

Language Selection

To change the language that the UConnect™ system is
using,

•

Press the ’Phone’ button to begin.

•

After the

⬙

Ready

⬙

prompt and the following beep, say

the name of the language you wish to switch to
(English, Espanol, or Francais, if so equipped).

•

Continue to follow the system prompts to complete
language selection.

After selecting one of the languages, all prompts and
voice commands will be in that language.

NOTE:

After every UConnect™ language change op-

eration, only the language specific 32-name phonebook is
usable. The paired phone name is not language specific
and usable across all languages.

For command translations and alternate commands in
supported languages, refer to “Command Translations”
at the end of this section.

Emergency Assistance

If you are in an emergency and the mobile phone is
reachable:

•

Pick up the phone and manually dial the emergency
number for your area.

If the phone is not reachable and the UConnect™ system
is operational, you may reach the emergency number as
follows:

•

Press the ’Phone’ button to begin.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2007 Ram Chassis Cab

Reviews:

Related manuals for 2007 Ram Chassis Cab

Brands by name

Popular brands

Dodge 2007 Ram Chassis Cab, Owner'S Manual

Search results

Summary of Contents for 2007 Ram Chassis Cab

Reviews:

Related manuals for 2007 Ram Chassis Cab

Brands by name

Popular brands