Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 318 | Manualshive

Page: 318 / 532

background image

Compact Spare Tire — If Equipped

The compact spare is for temporary emergency use with
radial tires. It is engineered to be used on your style
vehicle only. Since this tire has limited tread life, the
original tire should be repaired (or replaced) and rein-
stalled at the first opportunity.

WARNING!

Temporary use spare tires are for emergency use
only. With these tires, do not drive more than 50 mph
(80 km/h). Temporary-use spare tires have limited
tread life. When the tread is worn to the tread wear
indicators, the temporary use spare tire needs to be
replaced. Be sure to follow the warnings, which
apply to your spare. Failure to do so could result in
spare tire failure and loss of vehicle control.

Do not install a wheel cover or attempt to mount a
conventional tire on the compact spare wheel, since the
wheel is designed specifically for the compact spare.

Do not install more than one compact spare tire/wheel
on the vehicle at any given time.

CAUTION!

Because of the reduced ground clearance, do not take
your vehicle through an automatic car wash with the
compact spare installed. Damage to the vehicle may
result.

318

STARTING AND OPERATING

«
...
316
317
318
319
320
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Titanium Series

Brand: Fass Pages: 13

Brand: Kargo Master Pages: 6

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brand: Carbest Pages: 64

Brand: Honda Pages: 2

Advanced Million Color

Brand: LedGlow Pages: 4

Brand: Skoda Pages: 276

Brand: Mazda Pages: 7

Brand: Macally Pages: 10

Truck 2500 2018

Brand: RAM Pages: 32

Brand: Improved Racing Pages: 11

Brand: FORM FIT Pages: 4

AdvanceMobile VX1

Brand: AdvanceTec Pages: 20

Brand: Crux Pages: 8

Brand: Crux Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands