Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 48 | Manualshive

Page: 48 / 532

background image

WARNING!

Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use the
seat belt extender when the lap belt is not long
enough when it is worn low and snug, and in the
recommended seating positions. Remove and store
the extender when not needed.

Driver And Right Front Passenger Supplemental
Restraint System (SRS)—Airbag

This vehicle may have front airbags for both the driver
and front passenger (if equipped) as a supplement to the
seat belt restraint systems. The driver’s front airbag is
mounted in the center of the steering wheel. The passen-
ger’s front airbag (if equipped) is mounted in the instru-
ment panel, above the glove compartment. The words
SRS AIRBAG are embossed on the airbag covers.

These airbags are certified to the new Federal regulations
that allow less forceful deployments.

This vehicle may also be equipped

without

a passenger

side airbag. In this case the passenger side airbag will be
replaced with a storage bin.

48

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
46
47
48
49
50
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Daihatsu Pages: 485

Brand: REVCAMUK Pages: 4

Brand: Motoalliance Pages: 8

Brand: cam Pages: 28

Brand: Subaru Pages: 786

Brand: Beeper Pages: 2

Brand: Laser Pages: 3

Brand: Cadillac Pages: 538

QuadraTop Adventure Top 1113.00 Series

Brand: Quadratec Pages: 20

Brand: Cadillac Pages: 508

Brand: Kia Pages: 289

Brand: Ocular Pages: 7

Brand: Ferrari Pages: 45

Brand: K-Mate Pages: 11

Brand: Quadratec Pages: 8

QuadraTop Premium 11000.2335

Brand: Quadratec Pages: 16

Brand: SoundGate Pages: 12

Brand: Over Armour Offroad Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands