Docomo FOMA D851IWM, User Manual

Page: 282 / 460

280
Mo
ba
H
O
!/
Mu
sic
P
lay
er
/F
M R
a
dio
●
Reception will be paused in the following cases and
FM Radio reception will remain paused even after
the corresponding operation is completed. In these
cases, press
o
to restart reception.
･
When you receive a call and that call initiates 64k
data communication
･
When mail or a message R/F is received while
Display Priority is set to Show message .
･
When the time for an alarm or schedule item
arrives
･
When sounds for melody, i-motion, Flash, etc. are
played
･
When i-
α
ppli is started up
･
When the Mail Full Notification for Voice Mail
Service alarm rings
●
The following sounds will not be audible during FM
Radio reception (except while the function is
paused).
･
Keypad sound.
･
Charge alert
･
Open/close phone sound when opening/closing
the FOMA terminal
●
When the Battery icon is (battery level 1), a
message informing you that the battery is running
low will be displayed. If you do not perform any
operation on the FOMA terminal within about 1
minute after the message is displayed, the FM
Radio will automatically quit. To continue listening to
the FM Radio, select Yes .
●
Interference noise may be generated in the following
cases.
･
During recharging
･
When switching screens through key operation,
etc.
･
When in proximity to electronic devices
●
The sound emitted from the FOMA terminal speaker
is monaural.
●
It may be hard to hear the FM radio in certain
locations, such as indoors, where radio reception is
weak. In such cases, try the following remedies.
･
Extend the cords to the included remote controller
with microphone and the headphones with built-in
antenna, and move them to an angle that offers
better reception.
･
Move to a location close to a window, etc.
●
You can also listen to the FM Radio by connecting
the Desktop Cradle (sold separately) and an FM
antenna.
☛
P288
●
You can also connect the flat type earphone/
microphone set with switch (sold separately), etc., to
the earphone jack in order to listen to the FM Radio.
However, there is no guarantee of the quality of
receptivity in that case.
Selecting a station other than those in the area
selection screen
You can receive the broadcast from a station other
than those available in the area selection screen.
1
&
in the FM Radio screen
z
Highlight a
station
･
FM frequencies will advance in 0.1 MHz steps
and TV reception will advance one channel
each time
&
is pressed.
■ Selecting the station automatically (auto
station select):
&
(for over a second)
The radio will receive the broadcast from the
next available station on the frequency band.
･
If no stations can be received even after a
full scan of the frequency band, the radio
will return to the frequency that was being
received prior to pressing
&
.
･
To stop the auto station select scan, press
o
. Reception will then be accomplished at
the frequency that was being displayed at
the moment you stopped the scan.
･
During auto station select, Scanning will be
displayed.
■ Selecting a station by entering the
frequency:
a ( z
Select each item to set
b
Press
p
■ Selecting from the preset list screen:
p z 1
to
9
FM/TV : Press
1
to
4
to select either
FM or one of the TV channels TV
1ch to TV 3ch .
Frequency
: If you select
FM
, use the dial keys
to select the desired radio
frequency (76.0 MHz to 90.0 MHz).
76.0MHz 90.0MHz
TV 1ch TV 2ch TV 3ch
FM
R
a
d
io
MP#3̲E.book 280 ページ ２００６年３月８日 水曜日 午後５時１８分