Digi MIL-3000FTX Series User Manual Download Page 147

Page: 147 / 163

MIL-3000FTX Series of FastPort Print Servers

G-5

•

Auto-sense frame type

•

No primary server configured

•

Notification disabled

•

Queue scan rate: 1 sec

•

Netware Directory Services (NDS) enabled

•

Tree name:

•

Context:

•

Modify?, yes or no (y or n)?:n

G.8.1.4T—TCP/IP (Sockets, LPD, RARP, BOOTp, TFTP) Options

TCP/IP menu options

•

(E) Engine options (IP address,

RARP, BOOTP, etc.)

•

(S) Socket Options

•

(L) LPD Options

•

(X) Exit

E—TCP/IP engine options:

•

IP address: 0.0.0.0

•

RARP: Enabled.

•

BOOTP: Enabled.

•

BOOTP request interval: 2 hours.

•

Subnet Mask: 0.0.0.0

•

Default Router: 0.0.0.0

•

Syslog Host: 0.0.0.0 Syslog Priority: 2

•

Modify?, yes or no (y or n)?:n

G.8.1.4.1TCP/IP Menu Options: (S) Socket Options

TCP Sockets (fpfilter) options:

•

TCP Sockets (fpfilter) enabled

•

Auxiliary data ports:

•

Parallel 1

Parallel 2

•

Serial 1

Serial 2

Summary of Contents for MIL-3000FTX Series




































































































































































Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands

Digi MIL-3000FTX Series, User Manual

Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands