Digi MIL-3000FTX Series User Manual Download Page 104 | Manualshive

Page: 104 / 163

background image

MIL-3000FTX Series of FastPort Print Servers

10-5

10.4.1TCP/IP Config.

There are a series of choices that can be selected to configure FastPort on a
TCP/IP networks. The following is a hierarchy of the choices that can be
selected. To open each selection, use the mouse and follow the arrows to
the sub-menus.

Figure 10-8. TCP/IP Config. Select

Note:

The latest version of FastManage has an improved

TCP/IP Config

. screen. Contact

Digi’s LAN technical support for information pertaining to early versions of
FastManage and the

TCP/IP Config

. screen.

From

TCP/IP Config

., selections include:

•

IP Configuration

->

IP Address Properties

: Enables a user to change a variety of IP

options. Changes take effect at system reset. Options for this menu include
(Figure 10-9):

•

DHCP Enable

: Enables the DHCP feature. Default: Enabled.

•

DHCP Disable

: Disables the DHCP feature.

•

IP Address

: Changes the IP address of a device (e.g., if a device is

moved to a different subnet).

•

Subnet Mask

: Sets the subnet mask address for the device. If no IP

address is set, then default is 0.0.0.0. If an IP address is set, then:
– For Class A addresses, default is 255.0.0.0
– For Class B addresses, default is 255.255.0.0.
– For Class C addresses, default is 255.255.255.0

•

Gateway Address

: Sets up the address of the router that routes IP

packets across subnets. Default is 0.0.0.0.

Figure 10-9. Configure IP Address Properties Screen

«
...
102
103
104
105
106
...
»

Summary of Contents for MIL-3000FTX Series




































































































































































Reviews:

No comments

Related manuals for MIL-3000FTX Series

Brand: Oki Pages: 2

Brand: Oki Pages: 52

Brand: Oki Pages: 117

Brand: Oki Pages: 45

Brand: Oki Pages: 112

Brand: Oki Pages: 115

Brand: Oki Pages: 2

BladeCenter HS22

Brand: IBM Pages: 18

CLP-680ND: CLP-775ND

Brand: Samsung Pages: 2

Brand: Xerox Pages: 3

Versant 3100 Press

Brand: Xerox Pages: 45

Brand: Samsung Pages: 115

Brand: SMC Sierra Monitor Pages: 42

Document Centre 255 LP

Brand: Xerox Pages: 158

tecjet 6090DTG-dx5

Brand: TEC Pages: 73

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

Brand: Novexx Solutions Pages: 6

SMAVIA DMS 2400 II

Brand: dallmeier Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands