Digi MIL-3000FTX Series User Manual Download Page 105

Page: 105 / 163

MIL-3000FTX Series of FastPort Print Servers

10-6

•

FPFILTER Configuration

-->

Enable FPFILTER

: Enables host software services. Default:

Enabled

-->

Auxiliary ports

: Specifies the auxiliary ports for the parallel and serial

port printing. Default is

for each port.

Note:

The number of auxiliary ports to configure depends on the number of serial and
parallel ports on the FastPort.

•

LPD Configuration

: Enables BSD-type LPD print services and its options. Default: All are

Enabled

•

Restricted Hosts

: -->

Subnets

: Limits access to FastPort. Only hosts in the selected

subnet can access FastPort. Default for “Subnet” and “Mask” is

0.0.0.0

-->

Allowed IP Addresses

: Limits access to FastPort. Only the hosts with

the IP addresses can access FastPort. Default for all four fields is

0.0.0.0

10.4.2Novell Config.

There are a series of choices that can be selected to configure FastPort for a
Novell network, including:

Figure 10-10. Novell Config. Selections (Windows ‘95)

From Novell Config., selections include:

•

IPX Config.

-->

IPX SAP Name

: Changes the name used by the device in service

messages on the IPX network. This name displays in Map 1 of the Discovery
Application node. Default:

FPXXXXXX

, where “XXXXXX” is a the last six digits

of the MAC address.
-->

IPX SAP Interval

: Configuring the SAP internal of the device (numbers

are between 1-6). Default:

-->

IPX Traps

-->

Enable IPX Traps

: When enabled, the software sends

“traps” to a designated system. Default:

Enabled

. For more

information on traps, refer to “Traps” on page 2 and “IPX Trap
Hosts” (next selection).
-->

IPX Trap Hosts

: Designates to the system where traps will

be sent. Default for both “IPX Trap Host 1” and “IPX Trap Host
2” are all zeros.

-->

IPX Enabled

: Enables/disables IPX protocol. Default:

Enabled

•

NDS Config

. -->

Enable NDS

: Enables/disables NetWare Directory Services. Default:

Enabled

-->

Preferred DS Tree

: Sets the “tree” where FastPort’s server and print

queues are defined. The name entered must be a valid “Tree” or “Context.”
The field is blank by default.

Summary of Contents for MIL-3000FTX Series




































































































































































Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands

Digi MIL-3000FTX Series, User Manual

Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands