Digi MIL-3000FTX Series User Manual Download Page 89

Page: 89 / 163

MIL-3000FTX Series of FastPort Print Servers

9-2

9.2 Launching Discovery

Figure 9-1. FastManage for FastPort menu

1. Double-click on the

Discovery Application

icon. The software

“discovers” all of the SNMP devices on the subnet.

2. Devices will now appear on Map 1 as “thumbnails,” which represents

each SNMP device (Figure 9-2).

3. Double-click on a thumbnail to display a full-screen image of that

particular SNMP device (refer to Chapter 10).

Figure 9-2. Map 1 Discovery Application

Note:

Discover uses three protocols to find SNMP devices: IP, IPX, and NetBIOS. This
means that if a device uses all three of these protocols, that device will be “discovered”
three different times on the Map.

Summary of Contents for MIL-3000FTX Series




































































































































































Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands

Digi MIL-3000FTX Series, User Manual

Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands