Digi MIL-3000FTX Series User Manual Download Page 144

Page: 144 / 163

MIL-3000FTX Series of FastPort Print Servers

G-2

G.3 D—Display Summary Configuration Parameters, Including

Command [?,C,D,E,F,H,I,L,N,P,Q,R,S,Z,*,+] --> d

FastPort Model 3200X

Firmware revision 6.1.18, Datecode 10.23.1998 18:50

Ethernet address:00 40 C8 00 0B 0B

IP address:0.0.0.0

AUI Network module installed.

Console status monitoring: Off

Network monitor password security: Off

Sockets (fpfilter) enabled.

LPD enabled.

Netware enabled.

Microsoft Windows print services.

HP DLC enabled.

AppleTalk enabled.

Parallel port 1 mode: Standard

Parallel port 2 mode: Standard

Serial port 1 config: Baud

Data

Stop

Parity

Flow

9600

None

Xon/Xoff

Serial port 2 config:Baud

Data

Stop

Parity

Flow

9600

None

Xon/Xoff

(type “N” in monitor to view the network protocol parameters)

G.4 E—Display/Set Ethernet Options

Note:

Aux port is now set in the sockets section of the Network protocols menu)

Link test is currently enabled. Link test:

1.(disabled)

2.(enabled)

<enter> (don't change/continue)

Link test is now enabled

G.5 F—Flash Firmware Load Enable/Disable

Flash load is enabled.

•

This Bank: Vers. 6.1.15, Datecode 12/2/1997 13:25, (in
Bank #1, seqNum=10)

•

Other Bank: Vers. 6.0.29, Datecode 2/25/1997 12:20, (in
Bank #0, seqNum=9)

Flash load currently is enabled. Disable, yes or no (y or n)?:n

Special Options for Flash Code Image Control:

1.(Restart Running Image in Other Bank)

2.(Copy This Image into Other Bank)

Summary of Contents for MIL-3000FTX Series




































































































































































Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands

Digi MIL-3000FTX Series, User Manual

Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands