Digi MIL-3000FTX Series User Manual Download Page 116

Page: 116 / 163

MIL-3000FTX Series of FastPort Print Servers

B-2

Users should now be able to browse FastPort just as they would any
normal NetBIOS client. As an alternative:

1. Use the

net use

and/or

net view

command without having FastPort

in the same workgroup as the workstation.

2. Fill in the proper NetBIOS name of FastPort.

3. Type

net?

at the DOS prompt to get more info. on the utilities.

B.2 Troubleshooting DOS Tools

B.2.1 DOS Tools

If there are problems installing and using the NetBIOS management tools,
here are few suggestions:

• When using

showprn.exe

, and FastPort does not appear; issue the

command with:

-d0

-d1,-d2

-d3,-d4

-d5,-d6

, or

-d7

switch:

showprn.exe -d1

This causes

showprn

to use an alternate stack to send the packet. This

problem shows up sometimes in systems that have multiple NICs or
multiple protocols loaded. If a

-d1

switch was used with the

showprn.exe

tool, use it on the

NBMON

command line:

nbmon fpxxxxxx -d1

• If the IPX is loaded and running on a system running Windows 95, the

check box for

Send NetBIOS over IPX

should not be checked.

Send NetBIOS over IPX

is located in the Control

Panel--> Network--> IPX Compatible Protocol screen.

• Open up the Control Panel-->Networks screen. Choose NetBEUI

protocol. Check the check-box marked

Set this Protocol to be

the Default Protocol

. In Windows 95, it is located in the

Advanced Options menu.

B.3 After Upgrade

An older FastPort that has recently been flash updated to version 6.1 may
be configured with the invalid workgroup

WORKGROUPS

. Reset the device

to factory defaults. This will give FastPort the valid default workgroup
value

WORKGROUP

Summary of Contents for MIL-3000FTX Series




































































































































































Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands

Digi MIL-3000FTX Series, User Manual

Search results

Summary of Contents for MIL-3000FTX Series

Reviews:

Related manuals for MIL-3000FTX Series

Brands by name

Popular brands