D/43
-
ATTENTION
:
- Read the SAFETY REGULATIONS (contained in this manual) carefully for the safety of all personnel and your vehicle.
ExTERNAl bOOM ChAINS
(fig.89/D)
lubrication
Lubrication allows the operator to:
- Interpose liquid between contact surfaces to diminish wear
and prevent seizure.
- Protect chains from rust.
- Reduce noise between the surfaces subject to collisions.
Lubrication must be carried out:
- Longitudinally, in an area where joints are only slightly
strained to favour lubrication penetration.
- Crosswise, between the plates to facilitate oil penetra-
tion in joints.
Oil viscosity must be suitable to the surrounding temperature.
Viscosity which is too low favours lubrication withdrawal and
viscosity which is too high hinders lubricants from penetrating
joints. For proper viscosity, refer to the table at the side (fig.90/D
)
.
- attEntion
In the event of special applications or use in adverse condi-
tions, consult a
diEci
service centre.
- pRohiBition -
IT IS prohibited to lubricate the chains using grease
Checking for wear
At prescribed intervals, verify:
- The installation geometry.
- The condition of the chain in order to analyse traces
of friction that may indicate incorrect installation ge-
ometry. Wear on the side plate profile due to contact
with pulleys and guiding systems. Wear on the sides
of the external plates and on the pin heads due to con-
tact with pulley flanges or with any guiding devices.
- Wear on chain joints both due to direct measurement of
its length with measurement instrument or a control sca-
le, and visually.
- Wear of Fleyer raising chain plates.
- attEntion -
The chains must be replaced when wear due to
lengthening exceeds 2%.
when the chain is replaced IT IS MANDATORy also to
replace the respective rollers.
(fig.89/D)
- attEntion -
IT IS MANDATORy TO uSE ThE I.p.D. to carry out the
maintenance/control operations.
Recommended viscosity
ISO vG (Cst)
Temperature (C°)
- 15 < T< 0
0 < T< 50
50 < T< 80
between 15 and 32
between 46 and 150
between 220 and 320
Internal width
Roller
diameter
External link
Bushing
Roller
Internal plate
Connecting link
External plate
Pin
Pitch
Internal link
(fig.90/D) Chain oil viscosity table
(fig.91/D) Components of a standard chain
Summary of Contents for Agri Farmer
