Desoutter CVIL II Operator'S Manual Download Page 47

Page: 47 / 80

01/2018

47 / 80

6159933780

Issue no: 09

CVIL II

8.1.1.3 - LEDS TEST menu

This menu allows for testing the LEDs located on the

front side of the CVIL and for testing the LEDs on the

tool.

8.1.2 - CHANNEL TEST menu

This menu is used to test the operation of the controller

and tool. There is a sequence of two tests:

● Reading the information contained in the tool

memory.

● Checking the servo drive board.

If an error arises, a message is displayed.

Press to display an additional error

message.

8.1.3 - COUNTERS menu

8.1.3.1 - Tool and controller counters

Legend

1 Controller counter

2 Spindle counter

3 SP. Maintenance counter

This menu allows the maintenance technician to know

the number of cycles run.

Legend

1 Reset counter

● The Controller counter shows the number of cycles

run since delivery.

● The Tot. (total) and Par. (partial) counters show the

number of cycles run by the tool.

● Select Reset to reset the partial counter of the tool.

Summary of Contents for CVIL II
















































































Search results

Summary of Contents for CVIL II

Reviews:

Desoutter CVIL II, Operator'S Manual, Page: 47 / 80

Search results

Summary of Contents for CVIL II

Reviews: