Dell PowerEdge C8000 Owner'S Manual Download Page 112

Page: 112 / 295

112

Using the System Setup Program

IPv6 Mode

Select Enabled in the IPv6 Mode option and press <Enter> to view the

following screen.

IPv6 Mode

Gateway MAC Address Sets the MAC address for the static IP address.
BMC NIC MAC

Address

Sets the MAC address for the BMC management port.

IPv6 Mode

(

Disabled

default)

Enables or disables the IPv6 internet protocol support.
If set to enabled, configure the IPv6 prefix, IP and gateway

addresses.

Option

Description

IPv6 AutoConfig

Enables or disables IPv6 auto configuration.

Option

Description

Summary of Contents for PowerEdge C8000








































































































































































































































































































Search results

Summary of Contents for PowerEdge C8000

Reviews:

Related manuals for PowerEdge C8000

Brands by name

Popular brands

Dell PowerEdge C8000, Owner'S Manual

Search results

Summary of Contents for PowerEdge C8000

Reviews:

Related manuals for PowerEdge C8000

Brands by name

Popular brands