manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Figure 105. Removing the GPU switch board

1.

GPU switch board

2. captive screw (2)

3. tab on the chassis (2)

Next steps

1.

Install the system top cover (front).

2.

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions
Before working inside your system
After working inside your system
Installing the system top cover (front)
Installing the optional GPU switch board

Installing the optional GPU switch board 

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 

perform troubleshooting and simple repairs as authorized in your product documentation, or as 
directed by the online or telephone service and support team. Damage due to servicing that is 
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 
that are shipped with your product.

NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be 
performed only by Dell certified service technicians.

NOTE: The switch board used in configurations A and B is not interchangeable with the switch 
board used in configuration G.

190

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

Xerox Phaser EX7750 Configuration Manual preview
Phaser EX7750
Brand: Xerox Pages: 220
Xerox Phaser EX7750 Quick Start Manual preview
Phaser EX7750
Brand: Xerox Pages: 28
Xerox DocuPrint 100MX Install Manual preview
DocuPrint 100MX
Brand: Xerox Pages: 2
ExtraHop Discover 3000 Deployment Manual preview
Discover 3000
Brand: ExtraHop Pages: 5
IBM eserver xSeries 440 Quick Reference preview
eserver xSeries 440
Brand: IBM Pages: 34
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
Hologic Cenova User Manual preview
Cenova
Brand: Hologic Pages: 30
Buffalo LPV4-U2-300S Quick Setup Manual preview
LPV4-U2-300S
Brand: Buffalo Pages: 2
Black Box PCA35A-R3 User Manual preview
PCA35A-R3
Brand: Black Box Pages: 30
Fujitsu PRIMERGY PG-RSBOP2 User Manual preview
PRIMERGY PG-RSBOP2
Brand: Fujitsu Pages: 68
Fujitsu SPARC Enterprise T5440 Server User Manual preview
SPARC Enterprise T5440 Server
Brand: Fujitsu Pages: 92
Fujitsu SPARC Enterprise T5140 Product Notes preview
SPARC Enterprise T5140
Brand: Fujitsu Pages: 138
Fujitsu SPARC Enterprise T5440 Server Service Manual preview
SPARC Enterprise T5440 Server
Brand: Fujitsu Pages: 214
Fujitsu SPARC Enterprise T5140 Installation Manual preview
SPARC Enterprise T5140
Brand: Fujitsu Pages: 130
Fujitsu SPARC M10-4 Service Manual preview
SPARC M10-4
Brand: Fujitsu Pages: 514
Extreme Networks ExtremeControl IA-A-305 Installation Manual preview
ExtremeControl IA-A-305
Brand: Extreme Networks Pages: 31
Extreme Networks EC8200A01-E6 Installation Manual preview
EC8200A01-E6
Brand: Extreme Networks Pages: 94
Lantronix CoBox-FL User Manual preview
CoBox-FL
Brand: Lantronix Pages: 135

Brands by name

Popular brands

Load more brands