manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Figure 47. Removing a 2.5 inch cabled hard drive (hard drive 2/C and hard drive 3/D) from the hard drive 

cage

1.

screw (8)

2. hard drive cage

3. cable routing clip

4. power cable

5. signal cable

6. hard drive 2/C

7.

hard drive 3/D

Next steps

1.

Install the hard drives.

2.

Install the hard drive cage cover.

3.

Install the hard drive cage into the hard drive cage slot in the chassis.

Related Links

Safety instructions
Installing a 2.5 inch cabled hard drive into the hard drive cage
Installing the optional 2.5 inch hard drive cage cover
Installing the optional 2.5 inch hard drive cage

Installing a 2.5 inch cabled hard drive into the hard drive cage

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 

perform troubleshooting and simple repairs as authorized in your product documentation, or as 
directed by the online or telephone service and support team. Damage due to servicing that is 
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 
that are shipped with your product.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Keep the Phillips #2 screwdriver ready.

3.

Remove the hard drive cage. 

4.

Remove the hard drive cage cover. 

124

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

IBM HS12 - BladeCenter - 8028 Service Manual preview
HS12 - BladeCenter - 8028
Brand: IBM Pages: 204
Supermicro SUPERSERVER 6021F User Manual preview
SUPERSERVER 6021F
Brand: Supermicro Pages: 116
HYVE AQUILADSF Manual preview
AQUILADSF
Brand: HYVE Pages: 22
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
IBM BladeCenter PN41 Problem Determination And Service Manual preview
BladeCenter PN41
Brand: IBM Pages: 88
Oase WECS II 2048/DMX/02 Operating Instructions Manual preview
WECS II 2048/DMX/02
Brand: Oase Pages: 67
IBM Netfinity Series Installation Instructions Manual preview
Netfinity Series
Brand: IBM Pages: 44
Fujitsu PRIMERGY TX2550 M4 Upgrade And Maintenance Manual preview
PRIMERGY TX2550 M4
Brand: Fujitsu Pages: 563
Vxl Itona C42 Specifications preview
Itona C42
Brand: Vxl Pages: 2
Intergraph InterServe 80 SL System Setup preview
InterServe 80 SL
Brand: Intergraph Pages: 106
Viavi Gen2 GigaStor Hardware Installation preview
Gen2 GigaStor
Brand: Viavi Pages: 7
Datum TYMSERVE 2000 Operation And Technical Manual preview
TYMSERVE 2000
Brand: Datum Pages: 54
Silicon Graphics SGI 1200 Series Quick Start Manual preview
SGI 1200 Series
Brand: Silicon Graphics Pages: 64
Silicon Graphics Rackable C2112-4RP9 User Manual preview
Rackable C2112-4RP9
Brand: Silicon Graphics Pages: 68
Silicon Graphics Rackable C2112-4GP3 User Manual preview
Rackable C2112-4GP3
Brand: Silicon Graphics Pages: 70
AirLive MFP-101U User Manual preview
MFP-101U
Brand: AirLive Pages: 113
3onedata NP5100 Series Quick Installation Manual preview
NP5100 Series
Brand: 3onedata Pages: 4
Supero AS1021M-UR Plus User Manual preview
AS1021M-UR Plus
Brand: Supero Pages: 104

Brands by name

Popular brands

Load more brands