manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Figure 9. Installing the system top cover (front)

1.

system top cover (front)

2. release tab (2)

3. system cover lock

Next steps

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

Related Links

Safety instructions
Removing the system top cover (front)

Removing the system top cover (back)

Prerequisites

CAUTION: Do not operate the system without the system cover. This can result in overheating 

and cause component damage.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Turn off the system, including any attached peripherals.

3.

Disconnect the system from the electrical outlet and disconnect the peripherals.

4.

Remove the system from the rack.

5.

Keep the Phillips #1 screwdriver ready.

Steps
1.

Remove the screws securing the system top cover to the chassis.

2.

Slide the system top cover toward the back of the system.

3.

Hold the cover on both sides, and lift the cover away from the system.

62

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

Mako 6500 Setup & Configuration Instructions Manual preview
6500
Brand: Mako Pages: 56
NComputing L130 User Manual preview
L130
Brand: NComputing Pages: 95
NEC Express5800/320Ma Planning Manual preview
Express5800/320Ma
Brand: NEC Pages: 80
NEC Express5800/320Ma Technical Reference Manual preview
Express5800/320Ma
Brand: NEC Pages: 90
IBM eServer 342 xSeries Installation Manual preview
eServer 342 xSeries
Brand: IBM Pages: 70
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
H3C UniServer R4900 G5 Operating System Installation Manual preview
UniServer R4900 G5
Brand: H3C Pages: 141
360 Systems MAXX-1200-HD Operation Manual preview
MAXX-1200-HD
Brand: 360 Systems Pages: 148
W&T Com-Server++ Manual preview
Com-Server++
Brand: W&T Pages: 228
TRENDnet TE100-PS3 Administrator User Manual preview
TE100-PS3
Brand: TRENDnet Pages: 135
Eneo GLS-2101 Instruction Manual preview
GLS-2101
Brand: Eneo Pages: 94
IBM totalstorage fastt100 Installation, User And Maintenance Manual preview
totalstorage fastt100
Brand: IBM Pages: 160
Sun Microsystems Sun Ray 150 User Manual preview
Sun Ray 150
Brand: Sun Microsystems Pages: 121
Infrant Technologies ReadyNAS Duo User Manual preview
ReadyNAS Duo
Brand: Infrant Technologies Pages: 98
Intergraph InterServe 90 System Setup preview
InterServe 90
Brand: Intergraph Pages: 102
NEC ExpressA1160 Brochure & Specs preview
ExpressA1160
Brand: NEC Pages: 4
NEC Express5800/T120e Specifications preview
Express5800/T120e
Brand: NEC Pages: 2
NEC Express5800/T120d Hardware Specificftion preview
Express5800/T120d
Brand: NEC Pages: 2

Brands by name

Popular brands

Load more brands