manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Control panel module

Removing the control panel module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 

perform troubleshooting and simple repairs as authorized in your product documentation, or as 
directed by the online or telephone service and support team. Damage due to servicing that is 
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 
that are shipped with your product.

NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be 

performed only by Dell certified service technicians.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Follow the procedure listed in the Before working inside your system section.

3.

Keep the Phillips #1 screwdriver ready.

4.

Remove the system top cover (front).

Steps
1.

Hold and pull the plastic pull tab to disconnect the control panel cable from the control panel 

module.

2.

Remove the screws securing the control panel module to the chassis.

3.

Lift the control panel module away from the chassis.

Figure 107. Removing the control panel module

1.

screw (2)

2. plastic pull tab

3. control panel cable

4. control panel connector 

192

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

TANDBERG VCS Administrator'S Manual preview
VCS
Brand: TANDBERG Pages: 276
R&S SpycerNode 2U12 User Manual preview
SpycerNode 2U12
Brand: R&S Pages: 136
MO-SYS VP Pro XR Manual preview
VP Pro XR
Brand: MO-SYS Pages: 26
Axis OfficeBasic USB Wireless G User Manual preview
OfficeBasic USB Wireless G
Brand: Axis Pages: 43
Kramer KN-100 Quick Start Manual preview
KN-100
Brand: Kramer Pages: 2
Octagon TRAX-10 Technical Manual preview
TRAX-10
Brand: Octagon Pages: 17
Polycom ReadiManagerSE200 Brochure preview
ReadiManagerSE200
Brand: Polycom Pages: 4
Abus TVVR70020 User Manual preview
TVVR70020
Brand: Abus Pages: 44
Supero SC835XTQ - R982B User Manual preview
SC835XTQ - R982B
Brand: Supero Pages: 80
Supero SUPER SUPERSERVER 6026TT-BIBQF User Manual preview
SUPER SUPERSERVER 6026TT-BIBQF
Brand: Supero Pages: 104
Supero FatTwin F617R2-F73 User Manual preview
FatTwin F617R2-F73
Brand: Supero Pages: 144
IBM 4252E1U Datasheet preview
4252E1U
Brand: IBM Pages: 2
GIGA-BYTE TECHNOLOGY AMD EPYC R183-Z92-AAD1 User Manual preview
AMD EPYC R183-Z92-AAD1
Brand: GIGA-BYTE TECHNOLOGY Pages: 168
Acnodes RMC 7132 User Manual preview
RMC 7132
Brand: Acnodes Pages: 98
AMX MAX-MMS-01S Installation Manual preview
MAX-MMS-01S
Brand: AMX Pages: 2
GRASS VALLEY K2 SOLO - Service Manual preview
K2 SOLO -
Brand: GRASS VALLEY Pages: 106
Gigabyte R163-Z32-AAB1 User Manual preview
R163-Z32-AAB1
Brand: Gigabyte Pages: 166
Inspur NX5760M3 User Manual preview
NX5760M3
Brand: Inspur Pages: 42

Brands by name

Popular brands

Load more brands