manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Figure 71. Removing cooling fan

1.

cooling fan (8)

2. cooling fan power cable

3. cooling fan connector on system board

4. cooling fan slot

Next steps

1.

Install the cooling fan. 

Related Links

Safety instructions
Before working inside your system
Installing a cooling fan

Installing a cooling fan

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 

perform troubleshooting and simple repairs as authorized in your product documentation, or as 

directed by the online or telephone service and support team. Damage due to servicing that is 

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 

that are shipped with your product.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Follow the procedure listed in before working inside your system.

3.

Remove the system top cover (front). 

Steps
1.

Hold the cooling fan by the sides with the cable end facing the system board.

153

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

IBM BladeCenter HS23 Service Manual preview
BladeCenter HS23
Brand: IBM Pages: 36
NEC Express5800/R310e-E4 User Manual preview
Express5800/R310e-E4
Brand: NEC Pages: 86
IBM P 615 series Service Manual preview
P 615 series
Brand: IBM Pages: 491
Supermicro SuperServer 1029P-MT User Manual preview
SuperServer 1029P-MT
Brand: Supermicro Pages: 123
Cisco Linksys WPS54G User Manual preview
Linksys WPS54G
Brand: Cisco Pages: 40
Lightwave Communications SCS3230 System Administrator Manual preview
SCS3230
Brand: Lightwave Communications Pages: 97
Hawking HWPS1UG Specification Sheet preview
HWPS1UG
Brand: Hawking Pages: 2
Hawking HMPS1U User Manual preview
HMPS1U
Brand: Hawking Pages: 37
TechnipFMC Proline Promass 300 EtherNet/IP Manual preview
Proline Promass 300 EtherNet/IP
Brand: TechnipFMC Pages: 36
Symmetricom SyncServer S100 User Manual preview
SyncServer S100
Brand: Symmetricom Pages: 166
VC Videocomponents 11902 Mounting And Operating Manual preview
11902
Brand: VC Videocomponents Pages: 84
VBrick Systems EtherneTV v4.2.1 Portal Server Admin Manual preview
EtherneTV v4.2.1 Portal Server
Brand: VBrick Systems Pages: 180
Dell EMC Generation 6 Installation Manual preview
Generation 6
Brand: Dell EMC Pages: 25
Dell EMC E46S001 Installation And Service Manual preview
E46S001
Brand: Dell EMC Pages: 184
New H3C Technologies iFIST User Manual preview
iFIST
Brand: New H3C Technologies Pages: 45
Intel SE7520AF2 Operating Manual preview
SE7520AF2
Brand: Intel Pages: 34
Intel S875WP1-E Specification preview
S875WP1-E
Brand: Intel Pages: 117
Xiva musicm8 User Manual preview
musicm8
Brand: Xiva Pages: 37

Brands by name

Popular brands

Load more brands