manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Steps
1.

Turn the system cover lock to the unlocked position.

2.

Press the release tabs on the system top cover, and slide the cover toward the front of the system.

3.

Hold the cover on both sides, and lift the cover away from the system.

Figure 8. Removing the system top cover (front)

1.

system top cover (front)

2. release tab (2)

3. system cover lock

Related Links

Safety instructions
Installing the system top cover (front)

Installing the system top cover (front)

Prerequisites

CAUTION: Do not operate the system without the system cover. This can result in overheating 

and cause component damage.

1.

Follow the safety guidelines listed in the safety instructions section.

2.

Ensure that all internal cables are connected and routed correctly.

NOTE: Closing the system cover with incorrect cable routing can damage the cables.

Steps
1.

Align the slots of the system top cover with the tabs on the chassis.

2.

Slide the cover toward the back of the chassis until it locks into place.

3.

Rotate the system cover lock to the locked position.

61

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

IBM BladeCenter HS23 User Manual preview
BladeCenter HS23
Brand: IBM Pages: 30
IBM System x3950 X6 Product Manual preview
System x3950 X6
Brand: IBM Pages: 53
Vxl Itona TC73yy Hardware User'S Manual preview
Itona TC73yy
Brand: Vxl Pages: 19
QNAP TS-130-US User Manual preview
TS-130-US
Brand: QNAP Pages: 39
sysmik ICS-709 Installation Notes For Electrical Personnel preview
ICS-709
Brand: sysmik Pages: 2
Harman AMX Vision2 V2-MASTER-1210 Quick Start Manual preview
AMX Vision2 V2-MASTER-1210
Brand: Harman Pages: 2
SafeNet ProtectServer External 2 Installation Manual preview
ProtectServer External 2
Brand: SafeNet Pages: 22
Raritan Dominion SX II User Manual preview
Dominion SX II
Brand: Raritan Pages: 99
HP ProLiant DL185 Quickspecs preview
ProLiant DL185
Brand: HP Pages: 38
HP ProLiant DL320 Generation 4 Maintenance And Service Manual preview
ProLiant DL320 Generation 4
Brand: HP Pages: 70
HP ProLiant DL288 GENERATION 6 User Manual preview
ProLiant DL288 GENERATION 6
Brand: HP Pages: 45
HP ProLiant DL360e Gen8 User Manual preview
ProLiant DL360e Gen8
Brand: HP Pages: 116
HP ProLiant DL20 Generation9 Overview preview
ProLiant DL20 Generation9
Brand: HP Pages: 48
HP ProLiant DL165 Quickspecs preview
ProLiant DL165
Brand: HP Pages: 38
HP ProLiant DL2000 Specification preview
ProLiant DL2000
Brand: HP Pages: 46
HP ProLiant DL360 Generation 5 Quickspecs preview
ProLiant DL360 Generation 5
Brand: HP Pages: 43
HP ProLiant DL165 G7 Maintenance And Service Manual preview
ProLiant DL165 G7
Brand: HP Pages: 118
HP ProLiant DL360e Generation 8 Quickspecs preview
ProLiant DL360e Generation 8
Brand: HP Pages: 64

Brands by name

Popular brands

Load more brands