Dell PowerEdge C4130 Owner'S Manual Download Page 15

Page: 15 / 217

uSATA SSD indicator codes

Figure 4. uSATA SSD indicators

uSATA SSD activity indicator

uSATA SSD status indicator

uSATA SSD

Table 4. Drive status indicator codes

Drive-status indicator pattern

Condition

Flashes green twice per second

Identifying drive or preparing for removal.

Off

Drive ready for insertion or removal.

NOTE: The drive status indicator remains off until
all hard drives are initialized after the system is
turned on. Drives are not ready for insertion or
removal during this time.

Flashes green, amber, and turns off

Predicted drive failure

Flashes amber four times per second

Drive failed

Steady green

Drive online

Flashes green for three seconds, amber for
three seconds, and turns off after six seconds

Rebuild aborted

Summary of Contents for PowerEdge C4130


























































































































































































































Search results

Summary of Contents for PowerEdge C4130

Reviews:

Related manuals for PowerEdge C4130

Brands by name

Popular brands

Dell PowerEdge C4130, Owner'S Manual

Search results

Summary of Contents for PowerEdge C4130

Reviews:

Related manuals for PowerEdge C4130

Brands by name

Popular brands