manualshive.com logo in svg

Dell PowerEdge C4130, Owner'S Manual

The Dell PowerEdge C4130 is a high-performance server designed to meet demanding workloads. Ensure you get the most out of your device with the comprehensive Owner's Manual, available for free download at manualshive.com. This manual provides detailed instructions and valuable insights to maximize the potential of your PowerEdge C4130.

Share
Download
background image

Removing the system top cover (front)
Removing the system top cover (back)

After working inside your system

Prerequisites

Follow the safety guidelines listed in the Safety instructions section.

Steps
1.

Install the system cover.

2.

If applicable, install the system into the rack.
For more information, see the 

Rack Installation

 placemat at 

Dell.com/poweredgemanuals

.

3.

Reconnect the peripherals and connect the system to the electrical outlet.

4.

Turn on the system, including any attached peripherals.

Related Links

Installing the system top cover (front)
Installing the system top cover (back)

Recommended tools

You need the following tools to perform the removal and installation procedures:

• Phillips #1 screwdriver
• Phillips #2 screwdriver
• #T6 and #T10 Torx screwdrivers
• Wrist grounding strap

System covers

The system cover protects the innards of the server and helps in maintaining air flow inside the server. 

Removing the system cover actuates the intrusion switch and aids in maintaining system security.

Related Links

Removing the system top cover (front)
Installing the system top cover (front)
Removing the system top cover (back)
Installing the system top cover (back)

Removing the system top cover (front)

Prerequisites

CAUTION: Do not operate the system without the system cover. This can result in overheating 
and cause component damage.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Turn off the system, including any attached peripherals.

3.

Disconnect the system from the electrical outlet and disconnect the peripherals.

60

Summary of Contents for PowerEdge C4130


























































































































































































































Reviews:

No comments

Related manuals for PowerEdge C4130

360 Systems V2000 Series Operation Manual preview
V2000 Series
Brand: 360 Systems Pages: 117
IBM x3800 - System - 8865 User Manual preview
x3800 - System - 8865
Brand: IBM Pages: 104
AIC SB401-MN User Manual preview
SB401-MN
Brand: AIC Pages: 88
ASROCK Rack 4U60L Series User Manual preview
4U60L Series
Brand: ASROCK Rack Pages: 51
IBM System x3610 User Manual preview
System x3610
Brand: IBM Pages: 90
Gigabyte R282-Z93 User Manual preview
R282-Z93
Brand: Gigabyte Pages: 120
Buffalo TeraStation TS-RXL/R5 User Manual preview
TeraStation TS-RXL/R5
Brand: Buffalo Pages: 91
Huawei XH628 V5 Quick Start Manual preview
XH628 V5
Brand: Huawei Pages: 2
Huawei X6800 Technical Manual preview
X6800
Brand: Huawei Pages: 52
Huawei V100R002C01 User Manual preview
V100R002C01
Brand: Huawei Pages: 122
Huawei U-SYS MRS6100 Technical Manual preview
U-SYS MRS6100
Brand: Huawei Pages: 131
Huawei UPS5000-E-****-FM series User Manual preview
UPS5000-E-****-FM series
Brand: Huawei Pages: 261
Antrica ANT-35000A User Manual preview
ANT-35000A
Brand: Antrica Pages: 68
Sony WG-C20 Series Quick Start Manual preview
WG-C20 Series
Brand: Sony Pages: 3
Sony 158WGC10A Quick Start Manual preview
158WGC10A
Brand: Sony Pages: 7
Sony MAV-2000 Operation Manual preview
MAV-2000
Brand: Sony Pages: 26
Sony MAV-1000 Operation Manual preview
MAV-1000
Brand: Sony Pages: 28
Sony IPELA PCS-RS Operating Instructions Manual preview
IPELA PCS-RS
Brand: Sony Pages: 37

Brands by name

Popular brands

Load more brands