Diagnostic Lights
To help you troubleshoot a problem, your computer has four lights labeled "1," "2," "3," and "4" on the front or back panel. The lights can be off or green.
When the computer starts normally, the patterns or codes on the lights change as the boot process completes.
If the POST portion of system boot completes successfully, all four lights display solid green. If the computer malfunctions during the POST process, the pattern
displayed on the LEDs may help identify where in the process the computer halted.
incorrectly installed.
If the computer does not boot, contact Dell for technical assistance (see
Contacting Dell
).
Blinking yellow
A power supply or system board failure has
occurred.
See
Power Problems
.
Solid green and a beep code
during POST
A problem was detected while the BIOS was
executing.
See
Beep Codes
for instructions on diagnosing the beep code. Also,
check the diagnostic lights to see if the specific problem is identified
(see
Diagnostic Lights
).
Solid green power light and no
beep code and no video during
POST
The monitor or the graphics card may be faulty
or incorrectly installed.
Check the diagnostic lights to see if the specific problem is identified
(see
Diagnostic Lights
).
See
Video and Monitor Problems
.
Solid green power light and no
beep code but the computer locks
up during POST
An integrated system board device may be
faulty.
Check the diagnostic lights to see if the specific problem is identified
(see
Diagnostic Lights
). If the problem is not identified, contact Dell for
technical assistance (see
Contacting Dell
).
CAUTION:
Before you begin any of the procedures in this section, follow the safety instructions located in the
Product Information Guide
.
NOTE:
The orientation of the diagnostic lights may vary dependent upon the computer type. The diagnostic lights can appear either vertical or
horizontal.
Light Pattern
Problem Description
Suggested Resolution
The computer is in a normal "off"
condition, or a possible pre-BIOS failure
has occurred.
The diagnostic lights are not lit after the
computer successfully boots to the
operating system.
Plug the computer into a working electrical outlet and press the power button.
A possible BIOS failure has occurred; the
computer is in the recovery mode.
Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer.
A possible processor failure has occurred.
Reinstall the processor and restart the computer.
Memory modules are detected, but a
memory failure has occurred.
l
If you have one memory module installed, reinstall it and restart the computer. (see
Memory
for instructions on how to remove and install memory modules.)
l
If you have two or more memory modules installed, remove the modules, reinstall one
module, and then restart the computer. If the computer starts normally, reinstall an
additional module. Continue until you have identified a faulty module or reinstalled all
modules without error.
l
If available, install properly working memory of the same type into your computer.
l
If the problem persists, contact Dell (see
Contacting Dell
).
A possible graphics card failure has
occurred.
l
If the computer has a graphics card, remove the card, reinstall it, and then restart the
computer.
l
If the problem still exists, install a graphics card that you know works and restart the
computer.
l
If the problem persists or the computer has integrated graphics, contact Dell (see
Contacting Dell
).
A possible floppy or hard drive failure has
occurred.
Reseat all power and data cables and restart the computer.
A possible USB failure has occurred.
Reinstall all USB devices, check cable connections, and then restart the computer.
No memory modules are detected.
l
If you have one memory module installed, reinstall it and restart the computer. (see
Memory
for instructions on how to remove and install memory modules.)
l
If you have two or more memory modules installed, remove the modules, reinstall one
module, and then restart the computer. If the computer starts normally, reinstall an
additional module. Continue until you have identified a faulty module or reinstalled all
modules without error.
l
If available, install properly working memory of the same type into your computer.
l
If the problem persists, contact Dell (see
Contacting Dell
).
Summary of Contents for OptiPlex 745c
Page 105: ...Back to Contents Page ...
