background image

30

make it again.

(5)  Solenoid   switch   or   absorbing   devices,  such  as   ICEL,   is   prohibited  to  connect

inverter output.

(6) To provide input over current protection and for convenience in maintenance, the

inverter should be connected to AC power through circuit breaker.

(7) Please use twisted wire or shielded wire above 0.75mm for the wiring of relay

input/output   loop(X1~X6,   FWD,   REV,   OC,   DO).One   end   of   shielding   layer

suspended, and the other side connected to PE grounding terminal of inverter,

wiring length less than 50m .

                           

Danger

(1) The cover can be removed only when the power is switched off, all the LEDs on the

panel are off and waiting at least for 10 minutes.

(2) Wiring work  can be performed  only  when the DC  voltage between P+ and P-

terminals is lower than 36V.

(3) Wiring work can only be done by trained or professional personnel.

(4) Before usage, check whether the mains voltage meets the requirement of inverter

input voltage.

3.4 Main Circuit Wiring

AC 
power

R(R)

T(T)

U

W

PE

V

M

DGI900

Circuit 
breaker

S

Summary of Contents for DGI900




























































































































































































































































Reviews: