DDC Total-AceXtreme BU-67301B Design Manual Download Page 13

Page: 13 / 141

O V E R V I E W

Data Device Corporation

DS-BU-67301B-G

www.ddc-web.com

1/14

- 32-bit PCI Target/Initiator Interface



Operates at up to 66 MHz



Target single-word reads as low as 125 ns for reads, and 60 ns for

writes



Target Word Bursts at PCI Clock Rate



PCI Initiator with built-in DMA Engine with 264MB/sec Burst Transfer

Rate for reduced host resources.

•

1 Dual Redundant MIL-STD-1553 Channel

- BC or Multi-RT with Concurrent Bus Monitor

- Support of MIL-STD-1553 A/B, STANAG-3838, and MIL-STD-1760

- 2 Mb (64K x 36) RAM

- Transmit Inhibit Ball for Monitor-only Applications

- BC Disable Ball for RT-only Applications

- 48-bit/100ns Time Stamp

- IRIG-106 Chapter 10 Monitor

•

1553 Bus Controller (BC)

- Highly Autonomous Controller, with 32-Instruction Set

- Streaming and Minor/Major Frame Scheduling of Messages

- High and Low Priority Asynchronous Message Insertion

- Modify Messages or Data while BC is running

•

1553 Remote Terminal (RT)

- Emulate up to 31 RT Addresses Simultaneously

- Multiple Buffering Techniques

- Programmable Command Illegalization

- Programmable Busy by Sub-address

- RT Auto-Boot Option for MIL-STD-1760

•

1553 Bus Monitor (MT)

- IRIG-106 Chapter 10 Compatibility

- Filter Based on RT Address, T/R bit, Sub-Address

- Advanced Bit Level Error Detection to Isolate Bus Failures

•

Advanced Data Handler (ADH)

- For BC, RT, and Multi-RT modes, Option to Combine Control/Status and

Data Structures into Consolidated Structures for each Message.

Summary of Contents for Total-AceXtreme BU-67301B














































































































































Search results

Summary of Contents for Total-AceXtreme BU-67301B

Reviews:

Related manuals for Total-AceXtreme BU-67301B

Brands by name

Popular brands

DDC Total-AceXtreme BU-67301B, Design Manual

Search results

Summary of Contents for Total-AceXtreme BU-67301B

Reviews:

Related manuals for Total-AceXtreme BU-67301B

Brands by name

Popular brands