[1654]
Feedback 1 [Unit]
View the value of Feedback 1. See also par. 20-0*.
[1655]
Feedback 2 [Unit]
View the value of Feedback 2. See also par. 20-0*.
[1656]
Feedback 3 [Unit]
View the value of Feedback 3. See also par. 20-0*.
[1660]
Digital Input
Displays the status of the 6 digital input terminals (18, 19, 27, 29, 32 and 33). Input 18 corresponds
to the bit at the far left. Signal low = 0; Signal high = 1
[1661]
Terminal 53 Switch Setting
Setting of input terminal 53. Current = 0; Voltage = 1.
[1662]
Analog Input 53
Actual value at input 53 either as a reference or protection value.
[1663]
Terminal 54 Switch Setting
Setting of input terminal 54. Current = 0; Voltage = 1.
[1664]
Analog Input 54
Actual value at input 54 either as reference or protection value.
[1665]
Analog Output 42 [mA]
Actual value at output 42 in mA. Use par. 6-50 to select the variable to be represented by output
42.
[1666]
Digital Output [bin]
Binary value of all digital outputs.
[1667]
Freq. Input #29 [Hz]
Actual value of the frequency applied at terminal 29 as a pulse input.
[1668]
Freq. Input #33 [Hz]
Actual value of the frequency applied at terminal 33 as a pulse input.
[1669]
Pulse Output #27 [Hz]
Actual value of pulses applied to terminal 27 in digital output mode.
[1670]
Pulse Output #29 [Hz]
Actual value of pulses applied to terminal 29 in digital output mode.
[1671]
Relay Output [bin]
View the setting of all relays.
[1672]
Counter A
View the present value of Counter A.
[1673]
Counter B
View the present value of Counter B.
[1675]
Analog input X30/11
Actual value of the signal on input X30/11 (General Purpose I/O Card. Option)
[1676]
Analog input X30/12
Actual value of the signal on input X30/12 (General Purpose I/O Card. Optional)
[1677]
Analog output X30/8 [mA]
Actual value at output X30/8 (General Purpose I/O Card. Optional) Use Par. 6-60 to select the var-
iable to be shown.
[1680]
Serial com. bus CTW 1
Control word (CTW) received from the bus master.
[1682]
Serial com. bus REF 1
Main reference value sent with control word via the serial communications network, such as from
the BMS, PLC or another master controller, for example.
[1684]
Comm. Option STW
Extended serial communication bus option status word.
[1685]
FC Port CTW 1
Control word (CTW) received from the bus master.
[1686]
FC Port REF 1
Status word (STW) sent to the bus master.
[1690]
Alarm Word
One or more alarms in a Hex code (used for serial communications).
[1691]
Alarm Word 2
One or more alarms in a Hex code (used for serial communications).
[1692]
Warning Word
One or more warnings in a Hex code (used for serial communications).
[1693]
Warning Word 2
One or more warnings in a Hex code (used for serial communications).
[1694]
Ext. Status Word
One or more status conditions in a Hex code (used for serial communications).
[1695]
Ext. Status Word 2
One or more status conditions in a Hex code (used for serial communications).
[1696]
Maintenance Word
The bits reflect the status for the programmed preventive maintenance events in parameter group
23-1*.
[1830]
Analog Input X42/1
Shows the value of the signal applied to terminal X42/1 on the analog I/O card.
[1831]
Analog Input X42/3
Shows the value of the signal applied to terminal X42/3 on the analog I/O card.
[1832]
Analog Input X42/5
Shows the value of the signal applied to terminal X42/5 on the analog I/O card.
[1833]
Analog Out X42/7 [V]
Shows the value of the signal applied to terminal X42/7 on the analog I/O card.
[1834]
Analog Out X42/9 [V]
Shows the value of the signal applied to terminal X42/9 on the analog I/O card.
[1835]
Analog Out X42/11 [V]
Shows the value of the signal applied to terminal X42/11 on the analog I/O card.
[2117]
Ext. 1 Reference [Unit]
The value of the reference for extended closed-loop controller 1.
VLT
®
AQUA Drive
Instruction Manual
8 How to program the adjustable frequency
drive
MG.20.M5.22 - VLT
®
is a registered Danfoss trademark
8-11
8