Danfoss MCA 194, Operating Instructions Manual

Page: 36 / 48

VLT 5000 series FC 302 series
Parameter 440 Process PID
proportional gain 7-33 Process PID
proportional gain
Data range 0.00 – 10.00 0.00 – 10.00
Table 5.167 Conversion of Parameter 440
VLT 5000 series FC 302 series
Parameter 441 Process PID
integral time 7-34 Process PID
integral time
Data range 0.01 – 9999.99 0.01 – 10000.00
Table 5.168 Conversion of Parameter 441
VLT 5000 series FC 302 series
Parameter 442 Process PID
differentiation time 7-35 Process PID
Differentiation Time
Data range 0.00 – 10.00 0.00 – 10.00
Table 5.169 Conversion of Parameter 442
VLT 5000 series FC 302 series
Parameter 443 Process PID diff.
gain limit 7-36 Process PID
Diff. Gain Limit
Data range 5.0 – 50.0 0.00 – 10.00
Table 5.170 Conversion of Parameter 443
VLT 5000 series FC 302 series
Parameter 444 Process PID
lowpass filter time Not supported
Table 5.171 Conversion of Parameter 444
VLT 5000 series FC 302 series
Parameter 445 Flying start 1-73 Flying Start
Options [0] Off [0] Disable
[1] On [1] Enable
Table 5.172 Conversion of Parameter 445
VLT 5000 series FC 302 series
Parameter 446 Switching
pattern 14-00 Switching
Pattern
Options [0] 60 AVM [0] 60 AVM
[1] SFAVM [1] SFAVM
Table 5.173 Conversion of Parameter 446
VLT 5000 series FC 302 series
Parameter 447 Torque
compensation Not supported
Table 5.174 Conversion of Parameter 447
VLT 5000 series FC 302 series
Parameter 448 Gear ratio Not supported
Table 5.175 Conversion of Parameter 448
VLT 5000 series FC 302 series
Parameter 449 Friction loss Not supported
Table 5.176 Conversion of Parameter 449
VLT 5000 series FC 302 series
Parameter 450 Mains voltage
at mains fault 14-11 Mains Voltage
at Mains Fault
Range 180 – 690 V 100 – 800 V
Table 5.177 Conversion of Parameter 450
VLT 5000 series FC 302 series
Parameter 453 Gear ratio,
speed close loop 7-07 Speed PID
Feedback Gear Ratio
Range 0.01 – 100.00 0.0001 – 32.0000
Table 5.178 Conversion of Parameter 453
VLT 5000 series FC 302 series
Parameter 454 Dead time
compensation Not supported
Table 5.179 Conversion of Parameter 454
VLT 5000 series FC 302 series
Parameter 455 Frequency
range monitor Not supported
Table 5.180 Conversion of Parameter 455
VLT 5000 series FC 302 series
Parameter 457 Phase loss
functions 14-12 Function at
Mains Imbalance
Options [0] Trip [0] Trip
[1] Warning [1] Warning
Table 5.181 Conversion of Parameter 457
VLT 5000 series FC 302 series
Parameter 483 Dynamic DC
link compensation Not supported
Table 5.182 Conversion of Parameter 483
Parameter Mapping Lists Operating Instructions
34 Danfoss A/S © Rev. 2014-03-06 All rights reserved. MG37E102
5 5