Danfoss MCA 194, Operating Instructions Manual

Page: 17 / 48

VLT 5000 series FC 302 series
Parameter
number 009 0-09 Performance Monitor
Parameter
number 010 0-10 Active Set-up
Parameter
number 011 0-11 Programming Set-up
Parameter
number 012 0-12 This Set-up Linked to
Options [12] DC link voltage
[V] [1630] DC link voltage [V]
[13] Thermal load,
motor [%] [1618] Thermal load, motor
[%]
[14] Thermal load,
VLT® [%] [1635] Inverter thermal [%]
[15] Running hours
[hours] [1501] Running hours [hours]
[16] Digital input [1660] Digital input
[17] Analogue input
53 [V] [1662] Analogue input 53 [V]
[18] Analogue input
54 [V] [1664] Analogue input 54 [V]
[19] Analogue input
60 [mA] [1662] Analogue input 53
[mA]
[20] Pulse reference
[Hz] [1651] Pulse reference [Hz]
[21] Ext. reference
[%] [1650] Ext. reference [%]
[22] Status word
[hex] [1603] Status word [hex]
[23] Brake effect/2
min [kW] [1633] Brake effect/2 min
[kW]
[24] Brake effect/sec
[kW] [1632] Brake effect/sec [kW]
[25] Heat sink temp. [1634] Heat sink temp.
[26] Alarm word
[hex]
[27] Control word
[hex] [1600] Control word [hex]
[28] Warning word 1
[hex]
[29] Warning word 2
[hex]
[30] Com. Option
warning [hex] [953] Com. Option warning
[hex]
[31] RPM [min] [1617] Speed RPM [min]
[32] RPM x scaling
[min] [1609] Custom readout
[33] LCP display text Not possible
Table 5.10 Conversion of Parameters 009 to 012
VLT 5000 series FC 302 series
Parameter 013 Local Ctrl./config Not converted
Table 5.11 Conversion of Parameter 013
VLT 5000 series FC 302 series
Parameter 014 Local Stop key 0-41 [Off] Key on LCP
Options [0] Disable [0] Disable
[1] Enable [1] Enable
[2] Password
Table 5.12 Conversion of Parameter 014
VLT 5000 series FC 302 series
Parameter 015 Local Jogging Not converted
Options [0] Disable
[1] Enable
Table 5.13 Conversion of Parameter 015
VLT 5000 series FC 302 series
Parameter 016 Local Reversing Not converted
Options [0] Disable
[1] Enable
Table 5.14 Conversion of Parameter 016
VLT 5000 series FC 302 series
Parameter 017 Local Stop key 0-43 [Reset] Key on LCP
Options [0] Disable [0] Disable
[1] Enable [1] Enable
[2] Password
Table 5.15 Conversion of Parameter 017
VLT 5000 series FC 302 series
Parameter 018 Lock for data
change
0-61 Access to Main Menu
w/o Password
Options [0] Not locked [0] Full access
[1] Lock [1] LCP: Read only
Table 5.16 Conversion of Parameter 018
VLT 5000 series FC 302 series
Parameter 019 Power-Up Mode 0-04 Operating State at
Power-up
Options [0] Auto Restart, use
saved ref. [0] Resume
[1] Forced stop, use
saved ref. [1] Forced stop, use saved
ref.
[2] Forced stop, set ref
= 0. [2] Forced stop, set ref = 0
Table 5.17 Conversion of Parameter 019
Parameter Mapping Lists Operating Instructions
MG37E102 Danfoss A/S © Rev. 2014-03-06 All rights reserved. 15
5 5