manualshive.com logo in svg

D-Link DGS-2000 Series, Reference Manual

Share
Download
D-Link DGS-2000 Series Reference Manual Download Page 47

4  Web-based Switch Configuration

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

4

4

0

0

 

 

Port (1-65535): 

The TCP port number. TCP ports are numbered between 1 and 65535. The well-known TCP 

port for the Telnet protocol is 23. 
 
Click 

Apply

 to make the configurations take effect. 

 

System > SSH Settings 

SSH configuration is 

Enabled

 by default. If user does not want to allow the SSH configuration, they only 

need to disable the SSH State.  

 

Figure 4.38 – System > SSH Settings

 

 
Port (1-65535): 

The TCP port number. TCP ports are numbered between 1 and 65535. The well-known TCP 

port for the SSH protocol is 22. 
 
Click 

Apply

 to make the configurations take effect. 

 

System > D-Link Discover Protocol Settings 

For the D-Link Discovery Protocol (DDP) supported device, this page is an option for user to disable DDP or 

configure the DDP packet report timer.  

 
D-Link Discover Protocol State:

 The default setting is 

Disabled

. 

 

Figure 4.39 – System > D-Link Discover Protocol Settings 

 
D-Link Discover Protocol Report Timer (Seconds):

 Configure the report timer of D-Link Discover Protocol 

in seconds. The values are 30, 60, 90, 120 or Never. The default is 30 seconds.

 

 
Click Apply to make the configurations take effect. 
 

System > Ping Test 

The Ping Test is a small program that sends ICMP Echo packets to the IP  address user specified. The 

destination node then responds to or “echoes” the packets sent the Switch. This is very useful to verify 

connectivity between the Switch and other nodes on the network.  

Summary of Contents for DGS-2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands