manualshive.com logo in svg

D-Link DGS-2000 Series, Reference Manual

Share
Download
D-Link DGS-2000 Series Reference Manual Download Page 21

1  Product Introduction

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

1

1

4

4

 

 

Rear Panel 

 

Figure 1.20 – DGS-2000-52MP Rear Panel 

 

Power:

 Connect the supplied AC power cable to this port 

 

LED Indicators 

The Switch supports LED indicators for Power, Fan, and Link/Act for each port. The following shows the LED 

indicators for the DGS-2000 series Ethernet Switch along with an explanation of each indicator. 

 

Figure 1.21 –LED Indicators on DGS-2000 series 

 

Location 

LED Indicative  Color 

Status 

Description 

Per Device 

Power 

Green 

Solid Light Power on 

Light off  Power off 

Fan Error 

Red 

Solid light  The fan has runtime failure and is 

brought offline. 

PoE Max. 

Amber 

Solid light 

The PoE Max LED lights up when 

the total PoE output of Switch 

reached or exceeded: 

DGS-2000-10P: 65 Watts 

DGS-2000-10MP: 130 Watts 

DGS-2000-28P: 193 Watts 

DGS-2000-28MP and DGS-2000-

52MP: 370 Watts 

In the meantime, no additional PoE 

device can be supported. 

Blinking 

Amber 

Total PoE output of Switch reached 

guard band mode. (Max. PoE 

budget < 7 Watts ) 

Light off 

When the system power usage 

does not reach the guard band 

range. 

LED Per 

10/100/1000Mbps 

Copper Port 

Link/Act 

Green/Amber 

Solid 

Green 

When there is a secure 1000Mbps 

Ethernet connection (or link) at any 

of the ports. 

Blinking 

Green 

When there is reception or 

transmission (i.e. Activity—Act) of 

data occurring at a 1000Mbps 

Ethernet connected port. 

Solid 

Amber 

When there is a secure 

10/100Mbps Ethernet connection 

(or link) at any of the ports. 

Blinking 

Amber 

When there is reception or 

transmission (i.e. Activity—Act) of 

data occurring at a 10/100Mbps 

Ethernet connected port. 

Summary of Contents for DGS-2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands