manualshive.com logo in svg

D-Link DGS-2000 Series, Reference Manual

Share
Download
D-Link DGS-2000 Series Reference Manual Download Page 20

1  Product Introduction

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

1

1

3

3

 

 

 

The front panel of the 

DGS-2000-52MP

 switch consists out of the following:

 

•

 

Power LED : 

The Power LED lights up when the Switch is connected to a power source. 

•

 

Fan Error: 

The FAN LED shows the status of the fans, light off indicates all fans work fine and the red 

light indicates that one or multiple fans are working abnormally. 

 

•

 

PoE Max:

 The solid amber of PoE Max LED indicates the Switch reaches the maximum power budget 

defined by the administrator via PoE System Settings page of Web GUI or the default power budget of 

370 Watts. The blinking amber of PoE Max LED represents the switch is in guradband mode (available 

power left is less 7 watts). 

•

 

Port Link/Act/Speed LED (1-52):

  The Link/Act/Speed LED flashes, which  indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When a port has an amber light, this indicates that the port is running on 10M or 100M. When 

it has a green light it is running on 1000M. 

•

 

Port Link/Act/Speed LED (49F-52F):

 The Link/Act/Speed LED flashes, which indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When the port LED glows in amber, it indicates the port is running on 100M. When the port 

LED glows in green, it is running on 1000Mbps. 

•

 

Mode:

 By pressing the Mode button, the Port LED will switch between 

Link/Act

 and 

PoE

 modes. 

•

 

Reset:

 Press the Reset button for 1~5 seconds to reset the Switch back to the default settings and led 

will be solid light with amber for 1 second. 
 

 

CAUTION:

  The MiniGBIC ports should use UL  listed Optical 

Transceiver product, Rated Laser Class I. 3.3Vdc. 

 

 

Si le transceiveur optique n'est pas livré avec l'appareil, le manuel 

d'utilisation doit comporter la description ci-dessous ou son 

équivalent :« Ce produit est destiné à être utilisé avec un 

transceiveur optique homologué UL,tension DC3.3V, classe laser 

I.  

 

 

NOTE:

 The port 1 ~ port 48 are PoE ports. When user press the 

Mode

 button to PoE mode, only port 1 ~ port 48 will light up. 

 

 

CAUTION:

  This equipment can  be connected only to PoE 

networks without routing to the outside plant. 

 

 

L’équipement est conçu pour une installation dans un bâtiment et 

ne doit pas être connecté à des réseaux exposés (installations 

extérieures), notamment des environnements de campus, et l’ITE 

doit être connecté uniquement à des réseaux PoE sans 

acheminement vers une installation extérieure." ou équivalent.

 

 

 

NOTE:

  Once user enter in loader mode, you can use DNA tool 

(standalone version 2.0.2.4 only (No support by Chrome 

DNA3.x.x.x)) to download the image or call D-Link Technical 

Support for further help. 

 

Summary of Contents for DGS-2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands