manualshive.com logo in svg

D-Link DGS-2000 Series, Reference Manual

Share
Download
D-Link DGS-2000 Series Reference Manual Download Page 121

4  Web-based Switch Configuration

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

1

1

1

1

4

4

 

 

 

 

NOTE: 

Unable to select Payload in a MAC ACL, 

or L2 Header in IP ACL.

 

 
3) After the

 Profile ID 

has been created, it will go back to the main Access Profile List page. 

 

ACL > ACL Finder 

The ACL Finder page is used to help user to find a previously configured ACL entry. To search for an entry, 

enter the Profile ID from the drop-down menu, select a port that user would like to view and click 

Find.

 The 

table on the lower half of the screen will display the entries. To delete an entry click the corresponding 

Delete 

button. 

 

Figure 4.171 - ACL > ACL Finder 

 

ACL > CPU Filter Configuration Wizard 

The CPU Filter Configuration Wizard will aid with the creation of CPU Filter Rules.  

 

Figure 4.172 - ACL > CPU Filter Configuration Wizard 

 
From:

 Specify the origin of accessible packets. The possible values are: 

Any - 

Indicates CPU Filter action will be on packets from any source. 

MAC Address - 

Indicates CPU Filter action will be on packets from this MAC address. 

IPv4 Addresses - 

Indicates CPU Filter action will be on packets from this IPv4 source address. 

IPv6 - 

Indicates CPU Filter action will be on packets from this IPv6 source address. 

To:

 Specify the destination of accessible packets. The possible values are: 

Any - 

Indicates CPU Filter action will be on packets to any source. 

MAC Address - 

Indicates CPU Filter action will be on packets to this MAC address. The field of 

format is xx-xx-xx-xx-xx-xx. 

IPv4 Addresses - 

Indicates CPU Filter action will be on packets to this IPv4 source address. 

IPv6 - 

Indicates CPU Filter action will be on packets to this IPv6 source address. 

Service Type:

 Specify the type of service. The possible values are: 

Any

 - Indicates CPU Filter action will be on packets of any service type.  

       

Ether type

 - Specifies an Ethernet type for filtering packets. 

       

ICMP All

 - Indicates CPU Filter action will be on all ICMP packets. 

       

IGMP

 - IGMP packets can be filtered by IGMP message type. 

Summary of Contents for DGS-2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands