manualshive.com logo in svg

D-Link DGS-2000 Series, Reference Manual

Share
Download
D-Link DGS-2000 Series Reference Manual Download Page 13

1  Product Introduction

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

6

6

 

 

I.  

 

 

NOTE:

  The port  1 ~ port 8  are PoE ports. When user press the 

Mode

 button to PoE mode, only port 1 ~ port 8 will light up. 

 

 

CAUTION:

  This equipment can  be connected only to PoE 

networks without routing to the outside plant. 

 

 

L’équipement est conçu pour une installation dans un bâtiment et 

ne doit pas être connecté à des réseaux exposés (installations 

extérieures), notamment des environnements de campus, et l’ITE 

doit être connecté uniquement à des réseaux PoE sans 

acheminement vers une installation extérieure." ou équivalent.

 

 

 

NOTE:

  Once user enter in loader mode, you can use DNA tool 

(standalone version 2.0.2.4 only (No support by Chrome 

DNA3.x.x.x)) to download the image or call D-Link Technical 

Support for further help. 

 

Rear Panel 

 

Figure 1.6 – DGS-2000-10MP Rear Panel 

 

Power:

 Connect the supplied AC power cable to this port. 

 

DGS-2000-20 

20-Port 10/100/1000Mbps, includes 4 SFP Combo Ports (100/1000Mbps)  Ethernet Switch. 
 

Front Panel 

 

Figure 1.7 – DGS-2000-20 Front Panel 

 

The front panel of the 

DGS-2000-20

 switch consists out of the following:

 

•

 

Power LED : 

The Power LED lights up when the Switch is connected to a power source. 

•

 

Port Link/Act/Speed LED (1-20):

  The Link/Act/Speed LED flashes, which  indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When a port has an amber light, this indicates that the port is running on 10M or 100M. When 

it has a green light it is running on 1000M. 

•

 

Port Link/Act/Speed LED (16F-20F):

 The Link/Act/Speed LED flashes, which indicates a network link 

through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to 

the port. When the port LED glows in amber, it indicates the port is running on 100M. When the port 

LED glows in green, it is running on 1000Mbps. 

Summary of Contents for DGS-2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands