Curve Beam pedCAT Operator'S Manual Download Page 78

Page: 78 / 168

0473

90001

Rev

07.26.13

Density Material

Expected HU value Ranges

AIR (black chamber): -1100 to -900

ACRYLIC (light gray chamber):

-50 to 200

LDPE (dark gray chamber):

-250 to -50

TEFLON (white chamber):

700 to 1200

Distance Measurement Accuracy (QA Phantom):

Evaluate Distance Measurement Accuracy

: In the currently open QA Phantom scan, Zoom into

the Axial View’s line pairs and make a distance measurement, using the Distance Tool, from
one end of the line pair set to the other end of the line pair set. The distance should be between
41.0 - 42.5 mm.

Consistency/Uniformity (Water Phantom):

To evaluate consistency, we will image the Water Phantom. Water phantom image may vary
from what was delivered with your machine.

1. The water phantom should be filled all the way to the top with distilled water, allow a bit

of air space at the top to close the container.

Summary of Contents for pedCAT









































































































































































Search results

Summary of Contents for pedCAT

Reviews:

Related manuals for pedCAT

Brands by name

Popular brands

Curve Beam pedCAT, Operator'S Manual

Search results

Summary of Contents for pedCAT

Reviews:

Related manuals for pedCAT

Brands by name

Popular brands