Curve Beam pedCAT Operator'S Manual Download Page 150

Page: 150 / 168

149

0473

90001

Rev

07.26.13

7. Mount the Varian Receptor Panel:

a. There are 3 cables to be attached.



CAT6 cable (cable tie this cable to the black clip to maintain security).



Power cable



Ground

cable

b. The Ground nut should be removed from its location, then attach the ground cable

and re-attach the Ground nut.

c. Attach the Panel with 4 Plate screws.



The Load position of the panel is in the Gantry “B” position, which is centered.



Begin by securing the first 2 screws (vertically) and then manually move the

panel to the Gantry Home position, which is rotated to the right, with your hands
and secure the other 2 screws (vertically).

Summary of Contents for pedCAT









































































































































































Search results

Summary of Contents for pedCAT

Reviews:

Related manuals for pedCAT

Brands by name

Popular brands

Curve Beam pedCAT, Operator'S Manual

Search results

Summary of Contents for pedCAT

Reviews:

Related manuals for pedCAT

Brands by name

Popular brands