Curve Beam pedCAT Operator'S Manual Download Page 167 | Manualshive

Page: 167 / 168

Curve Beam pedCAT Operator'S Manual Download Page 167

166

0473

90001

Rev

07.26.13

The Warning message reads:

Startup:

When the annual service is due, the message will display during the Startup

sequence. The user should click OK and then should contact CurveBeam technical
support who will schedule the service and maintenance. This message will repeat at
Startup until the procedures are completed. Once the procedures are completed the
warning message will be reset by CurveBeam technical support.

Scan:

When the annual service is due, the message will display in the Procedure Tab

when the OK button is clicked. When the message displays, the user should click OK
and then should contact CurveBeam technical support who will schedule the service and
maintenance. This message will repeat at Scan time until the procedures are
completed. Once the procedures are completed the warning message will be reset by
CurveBeam technical support.

«
...
165
166
167
168
»

Summary of Contents for pedCAT









































































































































































Reviews:

No comments