Crane Merchandising Systems BevMAX 4 Series, Technical Manual

Page: 29 / 105

28 of 104
switch on left side of Y motor assembly, red light is
for home switch for picker cup plunger. Press the
number 4 key and the display will show a set of
numbers (i.e. ###### # ###### #). To position test
press the following:
a. Shelf letter (A,B,C,D,E) to travel to
selected shelf.
b. Column number (1,2,3,4,5,6,7,8, & 9) to
travel to selected column.
c. Key “0” to cycle cup plunger to hit
column target.
d. Key “F” to return cup to home position.
e. Key
“ ” “ is all stop.
f. Press “CLR” key to return to “Position
Test”.
Coke Factory Setup
Set Hook Offset
–
Test Delivery Cup to Port
Alignment
:
This sub menu will be used to test the vend
mechanism alignment to the port area confirming the
proper X belt tension. Adjust Hook Swipe “X” Offset
(left to right). Press the number “4” key and the
display will show “Hook Swipe ####, 3310 counts = 1
inch”. For factory default setting see born on label
settings listed on service door. To change the off
set, pull the top left (white) door switch in the out
position to power the XY motors. Press the “
” ” key
once will automatically run the Delivery Cup
Assembly to the swipe position and allow specific
vender coordinates to be changed and saved in the
control board memory. Use the numbers on the key
pad to change the coordinates. Press the “
” ” key to
save the new setting and the Delivery Cup Assy. will
automatically go to the “Home” position, then move
back to the swipe position again. Press the “
” ” key
to send the Delivery Cup Assy. back to the “Home”
position and the programming will return to “Set
Hook Offset”. Press key 2 to go to next menu item.
Coke Factory Setup
Cup Sensor On/Off
– Turns Delivery Cup
Sensor On & Off
:
This sub menu will be used to set the Cup Sensor
On or Off. Press key 4 and the display will show
“Cup Sensor On”. Press the “4” key to toggle the
Extended Cup to the On setting. Factory default
setting beginning with software revision 700.21 is on.
Note: Cup Sensor Off setting is used in BevMax 4
with non Z Cup Coke Venders manufactured prior to
run 8843AH. Cup Sensor On is used in all BevMax 4
Venders produced on run 8843AH & higher or if
there is a problem in the cup the sensor can be
turned off. Press key 1 to return to “Cup Sensor
On/Off”.
Coke Factory Setup
Cup Test
–
Turns Delivery Cup Sensor On & Off
:
This sub menu will be used to test the operation of
the Delivery (Picker) Cup Assy and Sensor. Press
key 4 and the display will show “Cup Test”. Press
key 4 and the display will show “On:0 In:0 Out:0
Hm:1”. Note: The left door switch must be pulled to
the out position to perform this test.
Caution: XY
needs to be in the home position before
performing this test.
Press the “
”
” key and the
display will show “Cup Sensor On/Off On:0 In:0
Out:0 Hm:1”. Press the “
” ” key to toggle the Cup
Sensor to the Off setting. To test the Cup with the
Cup Sensor On, press the “
” ” key and Display will
show “Cup Sensor On - On:1 In:0 Out:0 Hm:1”. To
perform tests press the following:
a. Shelf letter (A,B,C,D,E) to travel to selected
shelf.
b. Column number (1,2,3,4,5,6,7,8, & 9) to
travel to selected column.
c. Key “0” to cycle cup plunger to hit column
target. The Out:0 will change to 1
momentarily and back to 0 and the Hm:1 will
change to 0 momentarily and back to 1.
d. Key “F” to return cup to home position.
e. If the delivery cup has a cup sensor in it,
place a package in the delivery cup and the
In:0 will change to In:1, remove package and
it will change to In:0.
There are 4 pieces of data shown on the
display labeled as “On”, “In”, “Out”, and
“Hm”.
“On” indicates whether the delivery cup
sensor if present is turned on or off. A “1”
indicates it is on and a “0” indicates it is off.
“In” indicates whether the delivery cup
sensor detects product in the cup. In order
to be detected the product must be placed in
the cup after the sensor was turned on. If a
product is in the cup when the sensor is
turned on, the sensor will not detect it. A “1”
indicates product is detected and a “0”
indicates it is not. When the sensor is turned
off, there will be a “0” regardless of whether
product is in the cup or not. The Yellow LED
on the controller also will be on when a “1” is
displayed.
“Out” indicates whether the picker out switch
is closed. A “1” indicates that the picker out
switch is closed and a “0” indicates it is
opened (plunger at home position). Please
note that the switch is moved by the cam,
not the picker. Pulling the picker out by hand
will not activate the switch. The cam position