13 of 97
to scroll through the test routines available. Press key
number 1 to return to “Test Modes”.
“Test Vend” - Vend Testing
This function allows you to test vend each column.
Press key number 4 and the display will show
“Column A1”. Press key numbers 2 or 3 to scroll
through the columns available to run in motor test.
Press and hold the Power Interrupt (PI) switch.
Press key number 4 to vend from the column
displayed. Press key number 1 will return to “Test
Vend”. Press key number 2 to scroll to next test
mode.
“Test Sel Switch” - Select Switch Test
This function allows you to test each selection.
Press key number 4 and the display will show
“Selection 4”. Then press any key and the display
will show the last key number pressed.
Press and hold key number 1 for approximately 5
seconds will return to “Test Sel Switch”. Press
key number 2 to scroll to the next test mode.
“Test Display” - Display Test
This function allows you to test all segments in the
display. Press key number 4 and a lower case
alphabet will display, then turn off , then an upper
case alphabet will display alternating until key
number 1 has been pressed to return to “Test
Display”. Press key number 2 to scroll to next test
mode.
“Test Relays” - RELAY TEST
This function allows you to test the relay electronic
control of the compressor (“Compressor #”), the
evaporator fan(s) (“Fan #”), and the sign front light
(“Light#”).
CAUTION: Disconnect power to the compressor
before testing the compressor relay. Failure to
disconnect power to the compressor before testing
the relay could result in damaging the compressor.
Press key number 4 and the display will show
“Compressor #”, where # is the state of the relay - 0
= not activated or off; 1 = activated or on. Press key
number 4 to toggle the relay on and off. Press key
number 2 to scroll to “Fan #”, where # is the state of
the relay - 0 = not activated or off, 1 = activated or
on. Press key number 4 to toggle the fan(s) on and
off. Press key number 2 to scroll to “Light #”, where
# is the state of the relay - 0 = not activated or off; 1
= activated or on. Press key number 4 to toggle the
lights on and off. Press key number 1 to return to
“Test Modes”. Press key number 2 to scroll to
“Password Entry”.
* “Password Entry” - PASSWORD
ROUTINE
This function allows you to enter the following routines
which are not accessible until the operator enters a
password, which is set as 4-2-3-1. To enter the
password, press key number 4 until the display goes
blank. Then press key number 2, then 3, then 1, and
then 4, and “Cash Counters” should appear on the
display. If not entered properly, the display will return to
“Password Entry” after approximately 16 seconds. If
entered correctly, the display will go to the next function
“Cash”.
* “Cash Counters” - CASH COUNTER
ROUTINE
This function will show the user the vender historical
total cash counted and the interval cash counted for
each selection for the vender. Press key number 4 and
“Cash Tot”/”######.##” will show on the display where
the 8"#” characters are the historical total cash counters
that have been recorded. Note: Leading zeros are not
displayed. Example: Display flashes “Cash Tot”, then
“262500”. This is $2625.00 historical total cash. Press
key number 2 to scroll to “Card Tot”/######.##”, where
the 8# characters are the historical card reader cash
counters. Note: Leading zeros are not displayed.
Press key number 2 or 3 to display “Cash Sel
A1”/”######.##” where the 8"#” characters are the
interval cash counters for that selection. Note: Leading
zeros are not displayed. Pressing key number 2 or 3 at
this time will scroll through the available selection cash
counters. Example: Display flashes “Cash Sel A1”,
then “520.50”. This is $520.50 interval cash for
selection A1. Press key number 1 to return to “Cash
Tot”/”######.##”. Press key number 1 to return to
“Cash Counters”. Press key number 2 to scroll to the
next routine.
* “Sales Counters” - SALES COUNTER
ROUTINE
This function will show the user the vender historical
total number of vends and the interval vends counted
for each selection for the vender. Press key number 4
and “Sales Tot”/”########” will show on the display
where the 8"#” characters are the historical total vend
counters that have been recorded. Note: Leading
zeros are not displayed. Example: Display flashes
“Sales Tot”, then “1325”. This is 1325 historical vends.
If in a BevMax 4 with a Snack Vender attached you will
also have available Drink Sales # & Snack Sales #.
Press key number 2 to display Drink Sales # (if Snack
Vender attached). Press key number 2 to display
Snack Sales # (if Snack Vender attached).
Press key number 2 to display “Sales Sel
A2”/”########”, where the 8"#” characters are the
interval vend counters for that selection. Note: Leading
zeros are not displayed. Pressing key number 2 or 3 at
Summary of Contents for BevMAX 4 Series
