Cordivari Bollyterm HP, Use And Installation Manual

Page: 26 / 64

- 26 -
Cod. 1910000001187 - nv01
English
water installations and general requirements of devices to prevent
pollution by backflow.
• Directive 2006/42/EC of the European Parliament and Council of
17 May 2006 relative to the machine and later amendments and
supplements (D. Decree Law 17/2010).
• Directive 2004/108/EC of the European Parliament and Council of 15
December 2004 on the approximation of laws of the Member States
relating to electromagnetic compatibility.
• Directive 2006/95/EC of the European Parliament and Council of 12.
December 2006 on the approximation of laws of the Member States
relating to electrical equipment designed for use within certain voltage
limits.
• Directive 2002/95/EC of the European Parliament and Council of 27
January 2003 on the restriction of certain hazardous substances in
electrical and electronic equipment (RoHS).
• Directive 2002/96/EC of the European Parliament and Council of 27
January 2003 on the waste of electrical and electronic equipment
(WEEE).
3. Tank
Cordivari
®
tanks have been designed and built for use in the production
and accumulation of hygienic-sanitary hot water by means of a thermal
exchanger, obtained with the use of removable, fixed or out of tanks
exchangers, powered from various types of thermal energy sources
(Thermal generator, Heat pump, Solar panel) which use water as thermo-
vector fluid.
Any use of this product differing from the use indicated in this document
releases the manufacturer from any responsibility and will entail the
forfeit of any form of guarantee.
The products covered by this document have been built in compliance
with Directive 2014/68/UE (PED) with relation to pressure vessels, in
relation to the fluid content and operating conditions provided for use.
3.1 Identification of tank category (Direttiva 2014/68/UE)
The full range of Cordivari
®
tanks have values lower than the threshold
values listed below:
• Vessel designed to contain water (group 2) with vapour pressure at
maximum allowable temperature lower than or equal to 0.5 bar over
normal atmospheric pressure (1013 mbar) maximum working pressure
PS > 10 bar, the product of PS • V > 10,000 [bar • L], PS > 1000 bar
• Pipes intended to contain water (group 2) with vapour pressure
at maximum allowable temperature lower than 0.5 bar over normal
atmospheric pressure (1013 mbar) maximum pressure of 10 bar,
diameter DN PS operative > > 200 product and P.S • DN < 5000 [bar
xmm].
Therefore, all Cordivari
®
tanks, as stated in Art. 4.3 and Annex II, Tables
4 and 9, are not CE marked. However, Cordivari S.r.l. guarantees,
as established by the Directive, correct structural practices (ensured
by the Quality Management Systems UNI EN ISO 9001:2000 – UNI
EN 14001:2004) which ensures safety in the use and manufacturer
identification.
4. Heat pump (HP)
The heat pump is a machine that has been designed and built
solely for the production of hot sanitary water in civil
environments, incompatible with toxic and flammable gases.
Use in environments where the air is mixed and/or altered by other
gaseous compounds and/or solid particles is therefore strictly prohibited.
Use of the device for purposes other than those intended or non-
compliance with what is described in this manual will automatically
invalidate any direct or indirect liability by the Manufacturer and its
Distributors.
The heat pump is CE marked as dictated by the European Community, with
Directives 2006/42/EC, 2006/95/EC, 2004/108/EC, and amendments.
4.1 Identification of Product
In compliance with Directive 2014/68/UE (PED) as well as
with the regulations No. 812/2013 and No. 814/2013 issued
by directive 2009/125/EC (ErP - Ecodesign Requirements
for Energy-related Products) and by directive 2010/30/EC (Energy
labelling of products), the technical and heat loss specifications
together with the energy categories are written on the labels/technical
sheets attached to product. Such labels/technical sheets must be
considered as an integral part of these instructions for use.
The product label Bollyterm
®
HP contains the following identification data
and the following technical data, the label on the Heat Pump identifies it
with the following data:
Product Identification
Manifacturer Identification
Serial Number Year of production
Product Code Product Description
Heat Pump Identification
Serial Number
Bar Code
Energy data on product labels/technical data sheetst
Product technical data
OPERATING
LIMIT
CONDITIONS
EXCHANGER STORAGE
HEAT PUMP
See product label
HEAT PUMP TECHNICAL DATA:
Power
230 V-1
PH-50 Hz Channelling ø min 180 mm
Noise
level
See
product
label
Refrigerant
See
product
label
Channelling L max 8 m
(1)
Absorbed
Power
(2)
486 W
(2)
Refrigeration
load
See
product
label
Useful pressure
60 Pa
COP
(EN 16147)
See
product
label
Thermal
output
Absorbed
power
x COP
(1) sum of the suction and delivery
(2) at the following conditions: Tair 20°C T water from 15 to 55°C
4.2 Heat pump operation
The Heat pump module produces sanitary hot water using established
technology that exploits the operating principle described below:
• The refrigerant changes state in the evaporator by taking heat from the
source at low temperature (outside air).
• The compressor, which is the heart of the system, raises the energy
level of the heat taken: the refrigerant, in fact, reaches temperatures of
around 90°C as pressure increases.