Conexant Fusion 878A Manual Download

Page: 162 / 180

6.0 Control Register Definitions–Function 1

Fusion 878A

6.2 PCI Configuration Registers (Header)

PCI Video Decoder

6-8

Conexant

100600B

0x50—Power Management Support Register

Bits

Type

Default

Name

Description

[31:24]

0x00

Pwr-Data

This field is used to report the state-dependent data requested by
Data_Select and scaled by Data_Scale. Optional and not supported.

[23:16]

0x00

PMCSR_BSE

Reserved for bridge support extensions.

[15]

PME_Status

Function does not support PME# from D3

cold

[14:13]

Data_Scale

This field indicates the scaling factor to be used when interpreting the value
of the Pwr-Data register. Optional and not supported.

[12:9]

0000

Data_Select

This field selects which data is to be reported through the Pwr-Data
register. Optional and not supported.

[8]

PME_En

Function does not support PME# from D3

cold

[7:2]

000000

—

Reserved

[1:0]

PowerState

(1)

This field determines the current power state of a function and supports
setting the function into a new power state.

00 = D0
01 = D1 (not supported)
10 = D2 (not supported)
11 = D3

hot

NOTE(S):

(1)

Attempting to set PowerState to D1 or D2 will result in no change of state for that 2-bit field.

2. Bits [15:0] are also known as the Power Management Control/Status Register or PMCSR.

Summary of Contents for Fusion 878A





















































































































































































Search results

Summary of Contents for Fusion 878A

Reviews:

Related manuals for Fusion 878A

Brands by name

Popular brands

Conexant Fusion 878A, Manual

Search results

Summary of Contents for Fusion 878A

Reviews:

Related manuals for Fusion 878A

Brands by name

Popular brands