Conexant Fusion 878A Manual Download Page 140

Page: 140 / 180

5.0 Control Register Definitions-Function 0

Fusion 878A

5.3 Local Registers (Memory Mapped)

PCI Video Decoder

5-22

Conexant

100600B

0x5B—Audio Reset Register (ARESET)

Upon reset, ARESET is initialized to 0x00.

0x060—AGC Delay Register (ADELAY)

Upon reset, ADELAY is initialized to 0x68.

0x064—Burst Delay Register (BDELAY)

Upon reset, BDELAY is initialized to 0x5D. BDELAY(0) is the LSB.

Bits

Type

Default

Name

Description

[7]

ARESET

This bit must be toggled high and then low to reset the audio circuitry. ARESET must
be toggled at least once anytime the audio path is enabled.

[6:0]

000000

Reserved

Must be set to zero for proper orientation.

Bits

Type

Default

Name

Description

[7:0]

0x70

ADELAY

AGC gate delay for back-porch sampling. Use the following equation to determine
the value for this register:

ADELAY = (6.8 µs × 4 × Fsc) + 15

Example for an NTSC input signal:

ADELAY = (6.8 µs × 14.32 MHz) + 15 = 112 (0x70)

Bits

Type

Default

Name

Description

[7:0]

0x5D

BDELAY

The burst gate delay for sub-carrier sampling. The following equation should be
used to determine the value for this register:

BDELAY = (6.5 µs × 4 × Fsc)

Example for an NTSC input signal:

BDELAY = (6.5 µs × 14.32 MHz) = 93 (0x5D)

Summary of Contents for Fusion 878A





















































































































































































Search results

Summary of Contents for Fusion 878A

Reviews:

Brands by name

Popular brands

Conexant Fusion 878A, Manual

Search results

Summary of Contents for Fusion 878A

Reviews:

Brands by name

Popular brands