manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 98 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 98

10   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer: Donna Hollas  Project: Compaq ProLiant ML330 Setup and Installation Guide  Comments: 

Part Number: 173868-001  File Name: J-INDEX.DOC  Last Saved On: 1/17/00 4:49 PM

slots

DIMMs   3-21
locating, illustrated   3-21

Smart Array Controller,

connecting   4-6

SmartStart

Diskette Builder   5-9
do not use with preinstalled

operating system   5-8

installing   5-8
Server Profile Diskette,

registration   2-6

support software   5-8

generating support diskettes   5-9
list of utilities   5-9

using with preinstalled

operating system   5-8

standard, features   1-2
statements defined

caution   viii
important   viii
note   viii
warning   viii

storage devices, removing and

replacing procedures   3-7

switching on server, illustrated   2-5
symbols

used in text   viii
used on equipment   ix

system board components

illustrated   1-6
server   1-6

system board switches,

settings   C-1

system IDs, system menu   5-4
system information, system

menu   5-4

T

tables

Drive Bay Components and

Dimensions   1-3

Drive Bay Dimensions   3-7
Expansion Slots   3-17
Front Panel Components   1-4
Internal SCSI

Components   4-3

Processor Speed Switch

Settings (SW1)   C-2

Rear Panel Connectors   1-5,

2-3

Server Feature Board

Components   1-8

Server Feature Board

Configuration Switch
Settings (SW1)   C-3

System Board

Components   1-6

System Configuration Switch

Settings (SW2)   C-2

Taiwanese Notice   A-5
tape drive

installation   3-14
installation, illustrated   3-15
removing   3-15

technical support

Compaq website   x
telephone numbers   x

telephone numbers

Compaq   A-3
Compaq authorized

resellers   xi

FCC information   A-3
technical support   x

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments