manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 72 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 72

5-8

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

f-ch5 Server Configuration and Utilities.doc  

Last Saved On: 

1/17/00 4:23 PM

SmartStart

The SmartStart and Support Software CD is used to load the system software,
thereby achieving a well-integrated server and ensuring maximum
dependability and supportability. The SmartStart CD contains diagnostic
utilities and ROMPaq tools.

NOTE:

  Do not use the SmartStart and Support Software CD for loading system software if

you purchased your system with a factory-installed operating system. Refer to the

Compaq Factory-Installed Operating System Software User Guide

.

To install the SmartStart and Support Software CD, run F10 

F10 

F10 

F10 setup (BIOS

Setup Utility) and configure the primary operating system. Next, follow
these steps:

 

1.

 

With your server powered up, press the disk eject button to open the
CD-ROM tray.

 

2.

 

Locate the SmartStart and Support Software CD in the Server Setup and
Management pack.

 

3.

 

Insert the SmartStart and Support Software CD in the CD-ROM drive
and restart the system.

NOTE:

  Handle the CD by its edges, not by the flat surfaces of the disc.

 

4.

 

When the busy indicator turns green, the SmartStart installation
sequence begins.

 

Refer to the SmartStart documentation included with your server to
install the operating system, create updated driver diskettes, and run
upgrade utilities.

Compaq Insight Manager

Compaq Insight Manager is the Compaq application for easily managing
network devices. Compaq Insight Manager delivers intelligent monitoring and
alerting as well as visual control of your Compaq devices. Documentation for
Compaq Insight Manager is available on the Compaq Management CD in
[CD-ROM DRIVE]:\

OVERVIEW.HLP

.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments