manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 24 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 24

2-2

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

c-ch2 Overview of Server Installation.doc  

Last Saved On: 

1/17/00 1:37 PM

Selecting a Site

Make sure that the installation area you select has the following features:

■

 

Sturdy, level installation site that includes dedicated and properly
grounded circuits, air conditioning, and static electricity protection

■

 

7.6-cm (3-in) clearance on all sides of server for proper ventilation

■

 

Separate electrical circuit for the server

CAUTION:

  Protect the server from power fluctuations and temporary

interruptions with a regulating uninterruptible power supply (UPS). This device
protects the hardware from damage caused by power surges and voltage spikes
and keeps the system in operation during a power failure.

Unpacking the Server

Unpack the server, keyboard, and cables according to the instructions and
illustrations printed on the Quick Start Poster.

Locating Materials

Locate the following materials that were shipped with your ProLiant ML330:

■

 

Keyboard

■

 

Mouse

■

 

Power cord

■

 

Documentation label inside the server (most of the option installation
and setup instructions are located on the label, which is attached to the
inside of the access panel). See Chapter 3, “Hardware Options
Installation” for instructions on removing the access panel.

■

 

Documentation and software packs inside the shipping box

In addition to these supplied items, you may need:

■

 

Torx T-15 screwdriver

■

 

Phillips screwdriver

■

 

Options or peripherals, such as expansion boards, monitors, uninterruptible
power supply (UPS), memory, or drives

■

 

Application software

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments