manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 12 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 12

Compaq Confidential – Need to Know Required

Writer: Donna Hollas  Project: Compaq ProLiant ML330 Setup and Installation Guide  Comments: 

Part Number: 173868-001  File Name: b-ch1 Server Features.doc  Last Saved On: 1/17/00 4:06 PM

Chapter 

1

Server Features

The Compaq ProLiant ML330 delivers the latest performance features at an
affordable price. As the primary server in a small-to-medium business, the
ProLiant ML330 is an ideal server for applications such as file/print, simple
database, and remote access. This business-critical server delivers Intel
Pentium III technology, Error Checking and Correcting Memory, easy
expandability, and leading server management tools such as Compaq Insight
Manager and BIOS Setup Utility. Server features include:

■

 

Intel 256-KB Pentium III processor with 133-MHz front side system bus

■

 

64 MB of PC133-MHz registered, Error Checking and Correcting
(ECC), Synchronous Dynamic Random Access Memory (SDRAM)
DIMMs, upgradable to 2 GB

■

 

Capacity for five 18 GB hard drives for a maximum of 90 GB of
internal storage

■

 

Four removable media bays (three available)

■

 

IDE CD-ROM drive

■

 

1.44-MB, 3.5-inch diskette drive

■

 

Integrated Single Channel Wide-Ultra2 SCSI Controller

■

 

Integrated PCI 10/100 Wake-On-LAN NIC

■

 

Integrated ATI Rage XL Video Controller

■

 

Three available 32-bit PCI slots and two 64-bit PCI slots

■

 

CE Mark compliant power supply

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments