manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 92 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 92

4   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer: Donna Hollas  Project: Compaq ProLiant ML330 Setup and Installation Guide  Comments: 

Part Number: 173868-001  File Name: J-INDEX.DOC  Last Saved On: 1/17/00 4:49 PM

controllers

disk   1-7
IDE   5-5
network interface (NIC)   1-7
Wide-Ultra2 SCSI,

integrated   4-5

D

data back up   3-2, 5-3
date and time, system menu   5-4
dealers, locating   xi
device installation in 5.25-inch

drive bay, illustrated   3-13

diagnostic tools

ASR   1-9
configuring and managing

server with   1-11

DIAGS   1-9
POST   1-9

dimensions, drive bay   1-3
DIMMs

guidelines   3-20
installation

illustrated   3-22
instructions   3-22
sequence   3-21

removing   3-23
slots, illustrated   3-21
specifications   3-20
technical information   3-20

disk controller, features   1-7
Diskette Builder

operating systems   5-9
running   5-9

diskette drive, storage menu   5-5
drive bay

components   1-3
dimensions   1-3, 3-7

drive compartment removing,

illustrated   3-8

drive positions

illustrated   1-3, 3-7
maximum number   3-7

drive tray

removing   3-6
removing, illustrated   3-6
replacing   3-6

drives   

See 

diskette drive.

See 

CD-ROM drive. 

See 

hard

drives

E

electric shock icon   ix
electrostatic discharge   

See

 ESD

embedded devices, advanced

menu   5-6

equipment

Class A   A-2
Class B   A-2

ESD

damaged caused by   B-1
obtaining additional

information   B-2

parts

handling   B-1
sorting   B-1
transporting   B-1

precautions   B-1

European Union Notice   A-4
exclamation point icon   ix
expansion board

installing   3-18
installing, illustrated   3-19
removing   3-19, 3-24

expansion slots

location   3-17
location, illustrated   3-17
number   1-7

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments