manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 43 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 43

3-14

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

d-ch3 Hardware Options Installation.doc  

Last Saved On: 

1/28/00 2:13 PM

 

5.

 

Connect the data and power cables to the back of the device, as shown
in Figure 3-12.

 

6.

 

Replace the access panel and the front bezel. Restore power to
the server.

To install a tape drive:

CAUTION:

  Before removing the access panel, make sure that the server is

powered down, all cables are disconnected from the server, and the power cord
is disconnected from the grounded AC.

IMPORTANT:

 When installing a removable media device, remove the rails included in the

drive tray and install the rails on the device, replacing any existing rails on the device. The
rails are attached to the drive tray with two screws on each rail. 

 

1.

 

Follow the steps in “Removing the Access Panel” and “Removing the
Bezel Blanks” at the beginning of this chapter.

 

2.

 

To configure the device, set the SCSI device ID. You must manually set
the SCSI device ID on each device to a unique value in the range of
0 to 6 for each SCSI bus. Refer to the documentation provided with the
drive for instructions on how to set the SCSI device ID.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments