manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 48 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 48

Hardware Options Installation  

3-19

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

d-ch3 Hardware Options Installation.doc  

Last Saved On: 

1/28/00 2:13 PM

 

3.

 

Insert the expansion board into the slot and secure with a screw on the
top of the board.

Figure 3-19.  Installing an expansion board

 

4.

 

Connect any cables to the expansion board.

To remove an expansion board, reverse the above procedure.

Configuring PCI Devices

Interrupt sharing between PCI devices may occur in certain configurations.
The BIOS is designed to optimally configure the system. However, interrupt
conflicts may occur between PCI devices.

NOTE:

  Interrupt sharing does not present a problem for like devices, such as two network

interface controllers.

BIOS Setup Utility

NOTE:

  Interrupt settings can be reset at any time by running the BIOS Setup Utility, and

choosing “Set Defaults and Exit.”

The BIOS Setup Utility allows you to view and change the interrupt(s)
assigned to each device. However, you may notice that changing the interrupt
of one device changes another device interrupt.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments