manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 39 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 39

3-10

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

d-ch3 Hardware Options Installation.doc  

Last Saved On: 

1/28/00 2:13 PM

Removing a Hard Drive

To remove a 3.5-inch hard drive:

CAUTION:

  Before removing the access panel, make sure that the server is

powered down, all cables are disconnected from the server, and the power cord
is disconnected from the grounded AC.

 

1.

 

Follow the steps in “Removing the Access Panel” earlier in this chapter.

 

2.

 

Disconnect the power and data cables from the back of all devices in the
hard drive compartment.

Figure 3-9.  Disconnecting the hard drive cables

 

3.

 

Remove the three shipping screws, press the tabs on either side of the
drive compartment, then pull the drive compartment from the chassis as
shown in Figure 3-6.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments