manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 62 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 62

4-6

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

e-ch4 Cabling Guidelines.doc  

Last Saved On: 

1/17/00 4:20 PM

Connecting Internal Hard Drives to
Smart Array Controllers

Many configurations are possible when adding multiple SCSI controllers. This
section outlines the cabling procedure for the Smart Array Controller. Refer to
the Smart Array Controller options documentation for further information.

The following steps outline the installation procedure for the Smart Array
Controller:

 

1.

 

Follow the steps in sections “Installation and Removal Guidelines for
SCSI Hard Drives” and “Expansion Slots” of Chapter 3.

 

2.

 

Locate the Wide-Ultra2 SCSI cable attached to the Server Feature Board
SCSI connector.

 

3.

 

Remove the cable from the SCSI connector.

Figure 4-5.  Removing the Wide-Ultra2 SCSI cable from the
Server Feature Board

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments